I have an SM-ES3-24-P switch module that seems to be in a failed state. How can I revive it?#service-module gi 2/0 statusService Module is Cisco GigabitEthernet2/0Service Module supports session via TTY line 131Service Module is failedService Modul...
Forum Posts
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
Resolved! Routing rip issue
The routing table of router r2 and r3 aren't updating and their corrisponding hosts aren't able to communicate outside of the LAN. Hoping to get a reply asap..!
Hi guys, I'm new to packet tracer and I need to do a project, I'm really having a hard time getting this done, could you help me with it?I NEED TO PROPOSE A NETWORK SOLUTION USING VLANS ON EACH LAN SEGMENT AND CONFIGURING INTERVLAN ROUTING USING A LA...
Hi,I have a cisco ISR 4431 running version 17.3.2, from router internet is reachable but 8.8.8.8 is not pinging and whenever i try to run command license smart trust idtoken <token id>. I see there is not any error after running this command but stil...
Resolved! Vlan Translations or Swaps
Looking if anyone has a solution to this problem. I have a customer that refuses to change his VLAN number on his systems. I own his layer 3 SVI. I want to renumber the SVI as another customer on a target network I am migrating to owns it. What is a ...
I have a DHCP server in my project which gives all ip, also I need to make 4 pc which will have static ip, and I need to ping them with pc which has dhpc setting on pc with static ip how can I do it? I have one router. for examplePC59 > PC30PC30 ping...
Hello everyone, could you help me with commands to determine if a Cisco IOS XE router has any password expiration controls configured. I have tried several suggested commands and I cannot determine if there is any line with which I can support that t...
I'm using Windows 10 and Packet Tracer (PT) version 8.0 in 64 bit. The router 4331 in PT shown that it has 3 gigaethernet ports. The csreen capture is as follows.However, there are only 2 gigoethernet ports can be used while cabling and the screen ca...
Resolved! Acl-copp-management
Hi,can someone please advise why I need line 4 of below Acl? I understand we use established when we want to allow the response to the connection initiated from the internal network but on line 3 we allow ssh from any source to any destination alread...
Resolved! Configure DHCP server for VLAN
I am configuring a DHCP Server for a small VLAN.I have configured vlan 10 20 30 and trunk access for switch interfaces, activated fa0/0.1, fa0/0.2, fa0/0.3 as example belowint fa0/0.1 encapsulation dot1Q 10 ip address 192.168.10.1 255.255.255.0 ip he...
Hello All,I have a Cisco 1121-4P router running IOS XE 17.9.4a and I dont see the channel group option under any of the 4 switchports. The option shows up in WAN port, but I would like to utilize two switchports for the same VLAN and keep it under th...
CSR router R9 and R10 are suppose to form site to site IPsec VPN using digital certificate where R12 is the CA Server. R10#ping 40.0.1.1 so lo0Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 40.0.1.1, timeout is 2 seconds:Packet ...
Hi,Can someone help me in a problem related to HSRPMy standby router is not able to ping virtual ip, active router is pinging the same.My HSRP is working i.e shifting to other router.Noticeable thing 1. when i provide manual mac address then hsrp wor...
Good Afternoon, I know nothing about Cisco Switches or VLANs. We currently have a PfSense Firewall with VPN and conducting all of our VLAN routing to a Cisco Layer 2 Switch. Drawing and config files for PfSense and Layer 2 attached. I was tasked with...
