Hi Team, Two switches are connected to each and that link is a trunk port between those two switches, The challenge is on one switch when I perform cdp/lldp neigbor detail I can see the other switch which is connected to it but funny thing when I pin...
Forum Posts
Resolved! GNS3 - IOSvL2 crashing on boot
I get the following error message: https://pastebin.com/WEwAvbsCThe network is shown in the image. I literally just press start all devices, connect to console and get that. I tried googling the error but nothing shows up.
Hi All - I purchased a CBS220-24t-4G switch a couple weeks back and have been unsuccessful at resolving these two issues. When starting up the switch after the system states Starting Kernel... I receive the following error: "unknown rt error f030". H...
I have a new project that we are considering to use IE3400 Heavy Duty series switches to support the remote field sites. I have few design questions:Our network architecture includes a main hub site with core switches (standard Cat-9500 stack) and 22...
Hallo All! What is the reason that when enabling Telemetry on C9300 Series Switches, only Application Name, Usage and Througput are shown? Switches configured with telemetry show only Application Visibility (Name and Throughput) in DNA center. Why is...
Hello all,I have to provide IP for many clinets which each of them has to have individual VLAN ID. I am using q in q to provide ctag vlan under svlan.the configuration on my router is like below:ip dhcp pool SVL-200network 10.225.0.0 255.255.255.0def...
Hi all hoping someone can assist me.... I just purchased a Cisco Business 220 Series 16 port switch. I'm trying to do some basic configs via GUI. I created few VLANs and all I wish to do now is to add IPs to them. But for whatever reason when I se...
Hi guys, I'm new to packet tracer and I need to do a project, I'm really having a hard time getting this done, could you help me with it?I NEED TO PROPOSE A NETWORK SOLUTION USING VLANS ON EACH LAN SEGMENT AND CONFIGURING INTERVLAN ROUTING USING A LA...
I have two swithches both IE-3000-8TC i'm trying to set a trunk for them. Both these interfaces are duplex full, speed 100 and type 100BaseFX Fiber connections. switch a: interface 2/8switchport mode trunkduplex fullendswitch b: int Fa2/7switchport m...
i have a switch N9K-C93180YC-EX. when i insert optics to the switch the light in the optic comes up as soon as insert and very few seconds the optics light goes off. And hence not seeing the light on the fiber when connected to other device. what cou...
hi, I need help simulation high latency for ICMP , http and VOIP in cisco packet tracer. Basically what I'm trying to do is create two same topology where one is better than the other. But I do not know how to simulate the bad one by giving it very h...
hello everyone .I'm having a really big problem , I have the switch IE3300 8T2X Rugged Switch and I have a device that is controlled via ethernet.when I connect the PC and the Device through the Switch it lets me access the device but suddenly for so...
I have 2 Nexus 5Ks that drop ping packets when pinging between them at 70-90% drop rate. The ping drop rate also occurs for the following: - Between access layer switches and 5Ks - Between end user devices/servers and 5K - Between PC and HSRP gatewa...
Hello,I was told to propose a architecture in which Cisco 9500 switches to be used as a Core Switches in HA(SVL) and IE3400 switches will be used as a Distribution switches and they will for a Ring with REP Protocol. The distance between the IE3400 s...
Hi so we have a 3750G stack of 3, can ping the device, can snmp push and poll the device and syslogs are flowing. However We cannot ssh, telnet, http or https (all ports time out except 80/443 which actively refuse). I am trying to ssh/telnet from an...
