Hello, I have two 3850 with my Out of Compliance license, how can I solve this problem. Thank you and good day Kerwin
Hello, I have two 3850 with my Out of Compliance license, how can I solve this problem. Thank you and good day Kerwin
Hello, I'm looking to automate ping in packet tracer with Python. I made a script that works on PC Windows but not in PT. Error msg: AttributeError: '<invalid type>' object has no attribute 'system' in file Ping-PY.py on line 4 here is my script: imp...
The following command is configured for policy-based NAT (source nat) with VRF under the following conditions.Since it doesn't work properly, appreciate it if anyone could tell me how to fix. L3SWVRF name = VRF1000, Route-map name = NAT-MAP-1Source =...
When configured in a network bus topology, experiencing ping loss when 9 switches are connected. Is it likely a switch bandwidth issue? 9 units of C1000 equipment in a bus topology structure..
Hello. I have two 2960X switches in stack mode. I want to create an aggregation of two ports to two non-managable (external) switches and not Cisco. By default, by connecting both ports at the same time, the spanning-tree of the remote switches block...
I want to add my SW Catalyst Express 500 Series In my network park I found two problems: 1-It's impossible to have telnet to configure with putty 2-How to activate trunk mode on a port with the web assistant to see communicate with other Cisco switch...
Hi~ All Some documents say that only Active-standby has a copy of the config. Meanwhile, other documents state that all members have a config.https://community.cisco.com/t5/switching/what-happens-to-a-switch-s-config-when-it-is-removed-from-a/td-p/...
Hi everyone,I have a question about nexus 9805 power redundancy.It uses 3000w AC power and is connected to power supply slots 1, 2, 3, and 4.After testing the equipment, I found that the module worked properly when three power sources were connected....
Occurs in real time when connecting to the console. Log Contentsvss_cdp_tlv_receive_ Please advise which command does not display messages on the console. I think it's an error message, but why does it happen?
hi experts, I am learning router-on-a-stick routing, and router R1 is configured as follows: interface Ethernet0/3no ip address duplex auto!interface Ethernet0/3.1encapsulation dot1Q 10ip address 10.1.1.1 255.255.255.0!interface Ethernet0/3.2enc...
Hi, I am Jeong. I have configured HSRP with two ME3600X's.Same configuration, but they both stay in ACTIVE-ACTIVE configuration.HSRP operates separately and STANDBY is displayed as UNKNOWN. About 10 VLANs are in use and consist of interlinks and trun...
HelloI was using one HWIC-4ESW module on Cisco 2911/K9.But I didn't have enough ports, so I added HWIC-4ESW.And HWIC-4ESW showed abnormal movement. Both Interface and protocol came up, but the ping was not performed.What I checked was;1. The ping wen...
Hello, We have a Cisco C1000 switch that went into stack mode alone. I turned on the switch to modify some console settings and I have this message: *Mar 1 00:00:13.582: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack*Jun 17 13:48:00.4...
An error log has occurred on N9K recently. Please help to look into the cause.2022 Nov 24 15:38:26 DC_SW_9300_A %USER-3-SYSTEM_MSG: File Writing Failed for /mnt/pss/aaa_vdc_1.seqnum - aaad2022 Nov 24 15:38:29 DC_SW_9300_A Nov 24 15:38:29 %KERN-3-SYST...
hi, I am working on a ISP company. Is there any sloution about sleep mode switch at night? (like PC sleep mode) I am just focusing on the L2 switch. thank you!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM | ||
04-12-2024 01:38 AM | ||
04-06-2024 09:31 AM |
User | Count |
---|---|
11 | |
10 | |
8 | |
5 | |
5 |