Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
I try to install a Nexus9000v OVA Imgage on my ESXi6.5 Host. It doesn't matter if I use release 7.x or 9x it start's booting and stop as you can see in my pic below. Was anybody else able to get it run?
Hello Everyone, I got many snmp alert from WS-C4500X-32, for example Te1/1/2 Optical RX is to low (-40).Which is wired, I have never connected SFP modul at this port, and the ports config is empty.But, if I checked the inventory the switch says the S...
Hi I have a C4507 on which I did a write erase followed by a redundancy reload shelf. I went about configuring however, I forgot to enter username and set logging local on console and had to do reset. I pulled out the secondary and went about bootin...
Hi, how many 6504 can used to create VSS,i have 3 Cisco 6504 chase can add three ? Thanks and RegardsAni
I’m planning to upgrade to 7.3(6)N1(1) from 5.1(3)N2(1c). Can I use the following path: 5.1(3)N2(1c)>7.1(4)N1(1)>7.3(6)N1(1) Thanks in advance
If I utilize views, will it include everything except what exclude or only what I include? Basically I want to utilize views to prevent high CPU.Aslo, would using 256 bit AES matter much in terms of CPU?
Hi All,I have the problem and would like to have some advice , I have Cisco 4510R+E with 2 Sup-8e with SSO modeand I've noticed that no LED Uplink status for port 1-4 in standby supervisor and the physical link is down now.Anyone experience with this...
Hi everyone! I recently migrated all my old switches to the 9200 platform, but I was affected by this bug...https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvs27296Use PRTG, when monitoring any interface with SNMP spikes are generated, I have an open...
You basically can use the same NetFlow monitor and apply it under any VRF forwarding interface on a switch or router correct?
Dear networking experts, I have an ASA 5506-X and I use ASDM to manage the ASA. My end goal is to have a user connected to my Guest WIFI network access a host on my internal network. The job of the host is to authenticate the guest users and allow t...
I purchased this used a couple weeks ago, and have trolled all the forums I can find. I have this router connected to my home internet 192.168.1.254 on FastEthernet0/0. Then connected to a laptop on FastEthernet0/1. (I have a switch but I took it ...
Hello,We are using a couple of N9K-C9396PX switches in our datacenter and it seems there's a maximum of 507 VLANs in RPVST mode. A NX-OS 7.0.3.I7.7 is currently in use.In an effort to overcome this limit somehow, I'm now reading the Verified Scalabil...
Hi I created a route using the ip route command. I wanted to change one of the ip addresses . I tried doing the command over again, tried the prefix of no, still stays unchanged. also how do you use the search function on this forum and do quotes, ...
Hello, I have a router point to 2 firewalls in a high availability cluster (Checkpoint firewall). The firewall cluster has a virtual IP. I need to configure a static route on my router when the virtual IP on the firewall in the outgoing IP (i.e ip ro...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
11-10-2024 01:34 AM | ||
11-08-2024 02:07 AM | ||
11-06-2024 04:49 AM | ||
11-04-2024 07:57 AM | ||
10-25-2024 03:21 AM |
User | Count |
---|---|
16 | |
9 | |
5 | |
5 | |
5 |