Hi, Going from Access to Distribution layer Cisco's recommendation is a 20:1 subscription ratio. Is it possible to dynamically throttle switch ports (prevent devices from connecting at 1000M) once that uplink threshold is met? Regards,-Alex
Hi, Going from Access to Distribution layer Cisco's recommendation is a 20:1 subscription ratio. Is it possible to dynamically throttle switch ports (prevent devices from connecting at 1000M) once that uplink threshold is met? Regards,-Alex
Hello, We have a cisco Nexus9000 C93108TC-EX running NXOS: version 7.0(3)I4(7) where we can't get our port monitor to work. Below are the configs. Does anyone have any idea what we may need to add or take off? interface Ethernet1/13switchportswitch...
How I can allow PC1 from Subnet1 to FTP to PC2 on Subnet2 And block lower half of subnet1 using ACL. Basic topology is given below. PC1 ---------------Router1-------------------Router2-----------------PC2 NetID & Mask ...
when completing a very basic change over the weekend, a few of the switches in the stacks automatically rebooted:removing 802.1x from a stack of switches "Upon entering the script to revert (very basic "no auth open" script), stacks rebooted automati...
I am having trouble when I try to ping a pc from one router to another. For example PC0 to PC2 it gives me the "Destination host is unreachable" error and doesnt send the ping. However when I try to ping a pc on the same router, for example PC0 to PC...
Hey everyone, Couple of quick question i wanted to ask. My recently started at a new company, and they have 4 remote sites and an HQ site. All sites have their own independent DIA circuit which currently are plugged into Cisco ASA firewalls via out...
Hello got a kind of stupid question.Usually, when trying to access a normal server, we generate a key pair on a jumphost and move the public key to the server, so that we can always access the server from the jumphost (as per authentication). I know ...
Hello everybody I had a stack of 4 switches .. and need to split them to have 2 stacks... i wanted to access them using ssh and console cable... both stacks now show "access denied" when i put the passwordIs there any way to access them without reset...
Hi,how are you. I have a problem and i thought i should discuss it here. I want to access the other two switches so can i configure telnet on two other switches so that i can access them from any of the vlans configured on the switches and the infra...
Hi, I need to design a network which has currently very little resiliency, (no diverse routes or additional fibre and only a single core switch) however I believe designing it an G.8032 Ethernet ring will at least afford some fail-over benefits. What...
Hi All, I am looking for basic clarification on Cisco Stack Switch connection to Firewall HA pair. I am planning to have a Firewall Active/passive HA pair with port aggregation configured with LACP. Do i need to configure separate Port-channel in Swi...
HelloI will post the article here because this question.The question for OSPF.Am I more than trying a variety of routing's a wonder suddenly become, OSPF is why there is no "no auto-summary" of commands like protocols such as RIP and EIGRP?It's stran...
Hi Everyone's!I think about some config:eth 1/1 trunk with vlans: 1,2,3eth 1/2 access vlan 2eth 1/3 access vlan 3 in vlan 1 I have inner vlans: 11, 12, 13, 14,15 and:eth 1/11 is access for vlan11eth 1/12 is trunk for vlan12eth 1/13 is trunk for vlans...
Hey everyone, I am studying for my CCNA and I have aquired a 2960 WS-C2960-24TT-L switch (used).I am trying to acces the switch while conected to the console port.Everything loads up, but when I get the "Press RETURN to get started!" I cannot do anyt...
Hi folks,I am studying some questions for the exam and this question left me a little confused:Which of the following privilege level is the most secured?A. 0B. 1C. 15D. 16The answer is usually "C" (in all the discussions I found on the internet), bu...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-27-2024 06:10 AM | ||
09-25-2024 01:15 PM | ||
09-17-2024 12:44 AM | ||
09-13-2024 03:59 AM | ||
09-12-2024 02:06 AM |
User | Count |
---|---|
13 | |
8 | |
7 | |
7 | |
5 |