Hi,The default COS mapping for F2 card with egress queuing 1P3Q1T is: # show class-map class-map type queuing match-any 1p3q1t-8e-out-pq1 Description: Classifier for Egress Priority queue 1 of type 1p3q1t8e match cos 5-7 class-map t...
Forum Posts
I have a pair of Nexus 9396PX I'm trying to upgrade from 7.0(3)I2(1) to 7.0(3)I1(3). When I run the upgrade on both Nexus's this is what I get below. I also attached a txt file with the error that's more readable. Is this error normal or is there s...
Hi, I have a Cisco 2821 router. And I want to manage the router with SDM software. II have already installed the software and when i launched the application, 2 windows appear and the configuration page does not open. Can you please help me out. Rega...
I have 2x2800 routers with NME-16ES-1G-P - 16-port 10/100 Cisco EtherSwitch Service Module installed in it. I created L2tp tunnel using Physical interfaces on the routers. It works fine. laptops could ping each other. Now I Want to create a L2TPt...
Hi, Can someone explain why, when we redistribute: OSPF into EIGRP, the metric command is related to EIGRP. Such as: bandwidth value, delay value, reliability, effective bandwidth metric and MTU. Example: - router eigrp 100 - redistribute ospf ...
Hi,We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.Ca...
Hi guysDoes this software image supports QoS? If not, can you guide me which is the best one to use?I am having 4500E Sup 6L switch.Thanks!
HI Expert , i am planning to upgrade one of our production switch from 3:5:3E to 3:8:x , i am going to follow below process (1) copy tftp://<TFTP IP address>/<filename.bin> bootflash: (2) boot system flash bootflash:/<filename.bin (3) no boot...
7609 rsp720 pfc3cxl 6748 lan card and I config ingress egress police same time on interface SVIi config on two interface which in different vlan，and config ingress/egress qos police to 20m，but i found can’t work I can’t find hit in show policy-map in...
Resolved! Question about VLAN pruning...
As I understand it, VLAN pruning effectively prohibits the flooding of broadcast-type traffic (on a given VLAN) to switches without access ports in that given VLAN. so, my question is - given the topology depicted in the image I’ve included - if the ...
Resolved! Etherchannel on nexus 3048TP
hello, i need help for my problem. i am trying to configure LACP etherchannel between nexus 3048TP and catalyze the 2960s, the good news i have configured the LACP on 2960 s by following the procedure from cisco.com and success. But ... in nexus 3048...
Hi all. Im pretty new with cisco so i need help. Thanks alot :) So here is my case: I have 2 cisco 5508 WLC's, Catalyst 3650 and Aircap AP's First of all. I have all specs (ip's etc). Do i have to connect WLC together via redundancy before i ...
Resolved! 2 SG550-x switches wont communicate
Right now I have a firewall with a switch(BSW1) on the same and only vlan(vlan 1) that can communicate and the pcs can get out to the internet. I attached another SG550-x switch using an SFP cable on ports te1/0/2 on both switches. I am looking to ...
So I am setting up a proxy, and in an attempt to combat people not using the proxy or disabling it. I need some ACL's for our 2811 router. So that www traffic is denied unless through the proxy. So the proxy has the IP: 10.1.1.78 and my new acl's w...
| User | Count |
|---|---|
| 10 | |
| 8 | |
| 7 | |
| 6 | |
| 3 |
