Hello Guys, My company just buy building with Infrastsructure which is having 2 6504 E as core switches and 4506 connected with it access layer switches. all access layer switches connected with SFP ports to core switches (one port to each 6504 E s...
Dear Team, How to verify nexus 4k environment power status.
I am trying to build a new network using a 3560G and a C3900, from the 3900 I can reach directly to the internet however after connecting the switch I cannot ping the router from the switch nor can I reach the internet..... I have posted both configs...
Is there a NX 2k that has 4 SFP+ ports, can do routing (at least basic - static, basic EIGRP, OSPF) and do 802.1q trunking? If not, whats the smallest NX that has at least 4 SFP+ ports and can do routing (as above) and 802.1q trunking. Thanks!
Hi, I'm wondering if i have a breakout connection from 40G to 4*10G. What should be the configuration of the 4*10G ports, should it be port-channel to group the four 10G ports and do nothing on the other end of 40G?
Folks, couple concerns regarding this new switch we recently purchased... -Do you upgrade the firmware here the same way as you do with the lower end catalyst switches? -if we will only use this for a single network, in our case for iSCS traffic,...
Hi Frdz, We have CISCO7609-S (M8500) with RSP720, We observed below error with config register value. Configuration register is 0x2102 (will be 0x0 at next reload) ------------------ show version ------------------Cisco IOS Software, c7600rsp72...
Ok let's say you have SVI interfaces on a switch that connects to the servers (SVI 2 10.1.2.5, SVI3 10.1.3.5, etc.) and that switch connects to a router that has the sub-interfaces (int g0/0.2 10.1.2.1, g0/0.3 10.1.3.1, etc.). If the gateway configu...
Hi, I have a L3 3850 Stack with IP Base license and just need to enable multicast routing between two VLAN's (SVIA and SVIB) on the switch. (no other L3 PIM devices/transit). The switch uses static routing for unicast traffic via another SVI to an A...
Hi, we are integrating our switches / routers into Password Access Management tool. We need to create a user in the switch for that tool - so that when tool logs into the switch, it can only change passwords of other users. cannot do anything else I ...
Hi Guys,I'm trying configure access-list on port-channel in N7K.Ports connected to ESXi host with ~50 VMsI want to filter access for only 1 VM (with IP A.B.C.D), with no impact to other VMs. IP access list TEST 10 permit ip X.X.X.1/32 10.A.B.C.D/...
Hello, I've found the following OSPF configuration on my N9K, router ospf MPLS vrf MPLS router-id 10.10.255.0 default-information originate interface Vlan106 vrf member MPLS ip address 10.10.254.2/24 ip ospf priority 110 ip router ospf MPLS are...
So if I have two redundant (primary and secondary) switches so servers can connect to each for redundancy, I am not supposed to create the same SVI ips on each switch correct (excluding management SVI which I have as X.X.X.5 and sw2 .6)? I am not qu...
Hi, Should be an easy one. Concerned about causing issues to interface settings. Came across an incorrect switch setup and want to fix causing minimum disruption. 2x Stack 3750Switch 1 = MemberSwitch 2 = MasterSo Fa1/X/X is member Switch and Fa2/X/X ...
Hi I am trying to find the End of Support for Cisco Catalyst 4506-E Switch. Can anyone point me to the right link as I checked at the Cisco website , there isn't any information on this. Thanks.Regards, ken
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM | ||
| 05-27-2025 03:30 AM |
| User | Count |
|---|---|
| 9 | |
| 8 | |
| 7 | |
| 6 | |
| 5 |
