Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Can LACP priority help to make PO31 the active etherchannel over PO30 in my scenario? Image attached. Both LACP are currently setup with default priorities. Thanks! Dan

d front by Level 1
  • 3070 Views
  • 4 replies
  • 0 Helpful votes

I've been testing 2 C6840's, I would like to reset them back to defaults from out of the box. Is there any documentation on how to accomplish this. Thanks.

6tgreene by Level 1
  • 352 Views
  • 1 replies
  • 0 Helpful votes

Hi, I'm connected to the router console but, it always seems to get stuck and just sit there any way I can fix this?

Ed Lo by Level 1
  • 2124 Views
  • 4 replies
  • 0 Helpful votes

Hi, I erased the config file that the router came with and could no longer get to it through a browser using the default of 10.10.10.1 I've tried to cofigure back to how it was by assigning the 10.10.10.1 ip address to Ethernet port 0 and enabled htt...

Ed Lo by Level 1
  • 1023 Views
  • 1 replies
  • 0 Helpful votes

We have cutover to the Cisco Business Edition 6000M Svr (M4), Export Restricted SW (BE6M-M4-K9=) for UC. Two ports on this server are connected to our 2960S switch stack . The Server runs VmWare ESXi and the VMs related to UC – Communications manage...

I keep seeing these messages in my logs very frequently on a Nexus 5548UP.     %LLDP-3-DETECT_MULTIPLE_PEERS: Multiple peers detected on mgmt0Anyone have an idea of what might be causing these? Google has shown less than desirable amounts of informat...

Mierdin21 by Level 1
  • 11965 Views
  • 11 replies
  • 0 Helpful votes

Hi, I have a cisco 1841 router and Switch Jnuiper ex2200-24T. I have created new vlan for set of users and advertised that subnet in bgp. Please let me know how to pointing the reverse route of new VLAN subnet in router pointing to switch.

by Not applicable
  • 201 Views
  • 2 replies
  • 0 Helpful votes

Hello, as part of our normal switch build I notice these two commands are to be placed on every switch access port: switchport block multicast no ip igmp snooping tcn flood Are these two commands really necessary or recommended as standard procedur...

tedauction by Level 1
  • 14819 Views
  • 1 replies
  • 0 Helpful votes

Hi I got a bit of a peculiar problem which is driving me up the wall I recently upgraded a C3850 24t x 2 stack from 03.03.03SE to denali 16.3.3.  Ever since our client teams has not  been able to discover the thin/thick clients using option 203 on...

Resolved! cdp disable.....

Hi, I'm trying to analyze for the network at the new company. I noticed that all the routers and switches aren't enabled CDP... How should I analyze the network in a prompt way and easy way. I will very appreciate if you can help help me. Thank y...

ohforce55 by Level 1
  • 574 Views
  • 8 replies
  • 0 Helpful votes

Hi there! I have some questions about configuring QoS on the 3850's. We use them as Access-Switches and have a pair of 6840's to aggregate them. We only have L2 on the 3850, routing is done on the 6840's. Now, i need to configure QoS in the LAN and ...

Hi Team,  I want to migrate HP 2510 to Cisco 2900 series . I need your support regarding 802.1x implementation for Cisco  2960 and we have Microsoft NSP for dot1x.   Could anyone guide me further about it and I prepared the following template :- E...

UniWAQ by Level 1
  • 285 Views
  • 0 replies
  • 0 Helpful votes