Hi Experts I have to setup some SG300’s, 2960 switch stack and a Palo Alto firewall. The design states that I need to have VLAN1 shutdown and also place all unused VLANs into VLAN99. I will also have 3 more VLANs 66,77 and 5. VLAN5 will be my manag...
Forum Posts
Resolved! Quick PBR question
I have PBR setup to route a specific VLAN out a different gateway and this is what I configured to do it: ip access-list extended PBR-ACL permit ip 10.66.66.0 0.0.0.255 any route-map PBR-RM permit 10 match ip address PBR-ACL set ip next-hop 10.66.0....
Hi all, Could anyone confirm weather the IOS 15.4(1)SY2 support netflow feature ? I have checked the information on the webite http://cfn.cloudapps.cisco.com/ITDIT/CFN/jsp/by-feature-technology.jsp and realize that just the IOS 15.2 support the net...
I am looking to find more info about how exactly the command distribute-list filters for EIGRP and OSPF. There seems to be some big differences in how they interpret the in and out setting This is what I understand: For OSPF: IN - Filters what is ...
Hello everyone, this issue I'm having has me stumped so I've decided to try my luck at posting here. I've already browsed all the TFTPD forums looking for someone with the same issue but to no avail. I have a catalyst 3550 switch connected to a Wi...
Hi, i can not delete ntp server 118.163.81.61 but can not add new ntp server,change ntp server thank log, As described below
Resolved! Upgraded ROM
Hi! I have upgraded ROM on cisco WS-C4506-E. I can see on show version that its point to right version. ROM: 12.2(44r)SG10 But when I run show module I can see is its saying something different. Hw Fw Sw Status--+--------------------------------+--...
question one 1 about DHCP i have 3 routers, and do i put dchp on all of them. and how do i use the IP helper command. question 2 when making vlans on a switch like vlan 2 and vlan 45, and for example i go to g0/1 and i enable trunking and do the s...
I have two stacked 3650s that seem to be getting a good number of errors. Some interfaces its input errors some its output errors. What bothers me most is some of the interfaces have nothing plugged into them and some are disabled. This is just...
Resolved! Cannot ping SVI after power outage
After a power outage we are unable to ping our SVI. The vlans are showing up and up but I have no connectivity. The vlans that we cannot connect to are phone and camera vlans. The only solution I have found is going into the core switch for the site ...
Hi, I am confused and have following question reqarding SVI and VLANs. I am working on a lab and trying to establish HSRP between two Layer3 switches using an SVI. topologie used: ############ #######...
Hello Team, I have some troubles with some ISR's 2911.1.- SM-ES2-24-P: EtherSwitch SM L2 + PoE + 23 10/100 + 1 10/100/1000 on Slot 12.- CISCO2911/K9 chassis a) when I try to log in via telnet to the device does not respond, but if I send a ping this ...
Resolved! Host Findout
Hi dears I have cisco SG300/SG500/SF300 switch and 20 host are connected in every switch. My requirement is how to find that which host is connected to which port. I have mac address and ip address of that host. So please help me how to trace the ...
Hi Experts, I Have Just started actual hands on in Cisco Switching. Now I have to add new Cisco 4510 RE switch in our production network which is two layer topology (there is dual core of 6509 and distribution/access switches of 4500 series ). so...
