Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Ask Me Anything Event   Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from  Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...

rohit.png Vaibhav Aggarwal.png anuu.png Saquib Zeya.png

I am connecting a cisco 4500X to a checkpoint firewall PIM is enabled on the firewall but the switch is Just L2 I see the switch is receiving PIM Hellos and IGMP reports from the firewalls. but I don't see the port to the firewall as an mrouter port...

if MAC security drops a packet because it is OOO, will the interface increment the "input error" counter? if not, does the router increment any counter?

cp0983 by Level 1
  • 328 Views
  • 0 replies
  • 0 Helpful votes

Hello, Just getting APIC-EM 1.5 going to help us with a QoS re-deployment.  When I preview a generated policy (2960X access switch) for my test scope using the CVD defaults I do not get a voice ACL for classifying my Lync traffic.  There are ACLs for...

Hello My statement is correct about inconsistent state? If i do enable Root Guard feature on fa0/4 port then if this port will detect superior BPDUs then it will goes to inconsistent state. inconsistent state same like error disable state but little ...

nnn_sss22 by Level 1
  • 361 Views
  • 1 replies
  • 0 Helpful votes

Folks, I have a backbone ring with 3 cisco nexus 3064pq in layer 3 version 7 of the nx-os system. I use it for ospf v4 and v6, average traffic of 11Gbps with connection of 6 Bras pppoe. I'm noticing the very high usage of cpu for some processes like...

Hi, I just started to look into MPLS and found about VRF. How I understand about VRF is that it usually works with BGP. But when I see our core switch at work, I only see EIGRP with VRF, and as you know BGP isn't configured in Core switch... What...

ohforce55 by Level 1
  • 885 Views
  • 11 replies
  • 0 Helpful votes

Upgrading a NX 7K.A scp copy of SO image from a server to NX7K bootflash is very very slow.It took more than an hour to copy 30% of n7000-s1-dk9-npe.5.2.7.binDoes anybory have a sugestion ?Thanks Rosa

I have one interface g1/0/3 is flapping, but i go to sh int g1/0/3 Last clearing of "show interface" counters 1y5w. does it mean the interface is up for 1 year 5 week? which filed shows the up time for the interface? we have received alert of stp to...

Mary by Level 1
  • 385 Views
  • 2 replies
  • 0 Helpful votes

I need to configure port mirroring in both L2 and L3 switches. Purpose of mirroring is to monitor the utilization of existing check point Firewall which is connected in both switches through new Firewall. Below are the existing and proposed connectiv...

by Not applicable
  • 2324 Views
  • 3 replies
  • 0 Helpful votes

Hola. Tengo un switch sf200 -24p y el cooler del  mismo no corta nunca. otros switch de otras marcas que tengo si cortan y solo funcionan cuando por  la temperatura lo amerita. Es posible programar el mismo para que no funcione todo el tiempo ?

snovo by Level 1
  • 223 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card