Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Resolved! Isolated VLAN

I would like to set a isolated VLAN on multiple switches (nexus 5548), I would like to create such VLAN so its members can be accessible only from the same VLAN members. the setting is some end devices belonging to the same VLAN in the configuration ...

ben robin by Level 1
  • 3251 Views
  • 7 replies
  • 0 Helpful votes

I'm new to routing/switching and using Todd Lammle's study guide. After entering the ip and mask for a router-router connection I am getting 2 subnets and 2 masks where he gets a single subnet and mask. I know I must be missing something very obvious...

AlexG1 by Level 1
  • 13130 Views
  • 5 replies
  • 0 Helpful votes

good morning. I picked up a Catalyst 2950 for use in my house. It works fine but since I upgraded from 75/75 mps to 980/980 mps, the switch is only allowing speeds of 100 or less. I have no idea how to make changes to the configuration or if I can ev...

mike81 by Level 1
  • 1808 Views
  • 2 replies
  • 0 Helpful votes

Hello,I'm implementing a pair of 4510+E switch core, but I'm having a problem. There is a kind of module that the chassis is not recognizing (Unsupported module). Each chassi has:02x 8-E supervisor02x WS-X4748-RJ45-E02x WS-X4712-SFP-E02x WS-X4748-12X...

HelloI am new at networking and recently at an interview I was asked how to limit bandwidth (let's say to 1 Mbps) on Cisco 3560 and 3750 switches on a port level basis (for each PC that is connected to a port).What are the different ways and also the...

Hi everyone, I´m receiving this outputs :Feb  2 10:29:12.095 GMT-3-S: %OSPF-4-FLOOD_WAR: Process 1000 flushes LSA ID 10.219.245.211 type-2 adv-rtr 10.219.250.211 in area 11Feb  2 10:31:17.472 GMT-3-S: %OSPF-4-FLOOD_WAR: Process 100 re-originates LSA ...

Hi All, I need a help to define the best way to configure one new router in our customer.The scenario is: provide a ISR4331 with IOS SL-4330-IPB-K9 to connect at two ISP (different companies) with BGP protocol. My question is: Can we configure a load...

Is it possible to disable entering an enable mode on IOS ?Im deploying radius servers with two user groups (lvl 1 and lvl 15) my goal is to do that users who are lvl 1 would be not permited to enter enable mode.Yes, i know i can create a password for...

from88 by Level 4
  • 13028 Views
  • 8 replies
  • 0 Helpful votes

HI I have this digaram where i want OOB managment to be configured. means if some user wants to come from outside via FW and access my CORE switch.Internet--->FW-->3750 mgmt switch--->core switch--->access layer. for this purpose I want to create a L...

HiI am new in network management, I read about SNMP protocol, but I need to understand one point.We have a Server and a Switch with their SNMP Agents,The Server connectes to the Switch, Is it possible for The SNMP Agent in that Switch directly access...

RAlhanani by Level 1
  • 359 Views
  • 1 replies
  • 0 Helpful votes

Hello, Wondering if you can help me. I have a Cisco WS-C2960S-48FPS-L switch which connects some VOIP conference phones (Polycom SoundStation IP7000 or IP6000). The phones don't come up. It looks like the switch is not providing enough power. If I co...

Review Cisco Networking for a $25 gift card