Hello -
If I use 'no cdp enable' on interface config, are below two commands still relevant on the same interface config ? Hope 'no cdp enable' will disable all cdp traffic on the interface.
no cdp tlv server-location no cdp tlv app
Regards, Jr
Hello,
I would call my self a novice in the field of Networking (on a scale of 1 to 10, probably a 2), and I am asking for assistance in rectifying an error.
I have been trying to set up a LAN network for IP Cameras using the SRW224G4P network swit...
Hi, I have been trying to configure an asa 5512-x to pass multicast traffic from an outside network to an inside network as per the document :
PIX/ASA 7.x : Multicast on the PIX/ASA Platforms with sender on Outside Configuration Example
Document ID...
Hello,
We are looking at deploying ISR 4331 routers to replace some older 2811's. One thing that used to be true, in the 2800/2900's, was that if you had multiple layer 2 cards - like a NM-16ESW and an HWIC-4ESW for example - a physical link was re...
The new 1800 series ISR Routers have ADSL port and Wifi sopport?. Does thsi mena they can itself connect to Internet with ADSL card and act as a Wifi Router??
good day
i tried to configure 2921, ASR1000-x with OOB using ospf but my routers cant form adjacency please help here are my configs. using ip protocols on 2921 i can see the routed networks however on ASR1k i can only see routed protocols on the vrf...
Hello Guys,
I am facing latency problem for ESX hosts, anyone has idea to rectifiy it.
Ethernet15/12/22 is up
Hardware: 1000/10000 Ethernet, address: 5006.0411.4843 (bia 5006.0411.4843)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliab...
Network topology - router 3845 connect to the root switch Catalyst 5500 (CatOS), which is connected to the distribution switches 3508 and access switches 3524.
After a weekend half of 3524 is missing on 3 layer (cant ping), but the switches work pr...
I have a WS-C3560-48PS-S V07 The firmware on it now is c3506-ipbask9-mz.122-55.SE8.bin The latest is c3506-ipbask9-mz.122-55.SE10.bin
What (if any) is the difference between SE8 and SE10?
Hello everyone,
Why we configure bandwidth value to a interface ? Is it possible to utilize this value to rate limit ?
If I adjust the bandwidth for a one gig ethernet interface from 1000 to 10, what is the real transit capacity for this interface no...
In a L2 switch sending traps to a syslog server, the source IP traps, is the IP of the active vlan. ("Management vlan").
But in a L3 switch with many IP and vlans. What is the source IP of traps? Can I choose it?
In a real case,
Using many vlans 1-55...
Hi all;
Using EIGRP on a Cisco switch 3560-X with IPbase license. Is it supported?
Please note that the actual model number of the switch is WS-C3560X-24T-S and the IOS version is c3560e-universalk9-mz.150-2.SE9.bin.
Thanks
where can we download cisco active advisor. I goto cisco website, only cisco active network extraction 3.6.6 can be download provided user got license.
Hi,
I have a network topology with 2 PPPoE dialer interface from 2 different ISP's and both are pro actively monitored by IP SLA's. Implementing Policy Based routing, LAN 1 uplink use ISP1 gateway and the latter uses ISP 2 gateway. However, I ...
Hi There,
Just joined the Cisco Support Community and wondered if anyone can help...?
I'm currently learning to use Cisco switch and Routers and recently picked up a Cisco 1801 and a Cisco SG200-26P for home use which might seem a bit of an overkill...
