Hello, I'm trying telnet access to Switch4 using pc6. I connected switch2 switch1 and router using telnet without any problem. I did usual setup on switch but still not ping and can't access through telnet. I attached images So If anyone have Idea pl...
I was looking through the firmware for C11xx.There are 2 recommended firmware being version 17.9.4 and 17.6.5.Shouldnt there be only 1 firmware?Do people upgrade from version 17.6.5 to 17.9.4?What is the difference between Cupertino and Bengaluru?
hi all,i want to connect a 4510 to a sg350x, this is what i have done so far but no joyon the 4510interface GigabitEthernet1/2switchport access vlan 7switchport mode accessspanning-tree portfast disablespanning-tree bpduguard disableon the sg350xinte...
Hello,I apologize in advance if this is the wrong community. I'm working on a lab for a course and need some assistance with troubleshooting in Packet Tracer. There are supposedly two things wrong with the Packet Tracer configuration and I cannot see...
We have a pair of Nexus 9ks and a pair of Nexus 3Ks that we are configuring two VPCs between. There is one link between each 9K to each 3K that makes up the two different VPCs The port-channel interfaces and physical interfaces on the 9Ks have an m...
Hi Freindis there any configuration Example on how to Connect ACI Multisite using vPC as DCI Transport , apart around 50 KM from each other , L1 is Darkfiber (over DWDM Circuit) from MOCthanks
Hi Freinds Talking N7Kcan we configure L3 PC on different Line cards and Bundle them together in the Mgmt vrf acting HA for peer-keepalive link thanks
Hello there,Is there any way to get ports number appears like 48 ports in same slot (SW-9300-24P) started from (Gi1/0/1 to Gi1/0/48) , in my case the ports shown in the stack switches (Gi1/0/1 - 24 for active switch , // Gi2/0/1 - 24 for the standb...
Hi Freindsit seems OTV is much easier to configure for DCI instead of VxLAN BGP EVPN even with DCNM, So better to push OTV over VxLAN BGP EVPN, thus N7K instead of N9KFreinds Do y agree ? Thanks
Hello,I have stack of two Cisco CBS350-24XS switches.I use OOB mgmt interface for management. Both switches have connections to their Mgmt ports, but only Mgmt port of Active member has a link (UP state), Standby switch has no link (it is down).I gue...
Hi allI am new to deploying CPPM on my network for 802.1X authentication, MAC authentication and captive portal with Cisco switches.I would like to know if it's possible to use a single port for all three authentication methods - 802.1X, MAC authenti...
Hi, regarding my studies I would like to confirm the three statements below about spanning tree. When a switch boot or spanning tree is enabled on a switch, the switch ports pass into blocking state 20 seconds before going into listening state (I rea...
I installed two C1000-8T-2G-L and stacked them using SFPs from the front. Each time the two units are switched off, when powered back up, the second device becomes unknown on the stack. H/W CurrentSwitch# Role Mac Address Priority Version...
In the packet tracer project, I have 6 divisions, IT, HR, finance, and one called public. Pcs from IT, HR, and finance divisions need to have access to the public. Each division also has its respective VLANs assigned except public. So, I created sub-...
Hi FreindsvPC Failure Scenariowhat happens to traffic if 1st vPC peer-link goes down and after sometimes 2nd vPC Keep-alive went downThanks
