Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
I have been given some Cisco ACE 4710's to look after recently as part of an old contract for a customer. I have had to replace one of the units recently die to a hardware fault and I have the replacement unit from Cisco. I wanted to know if there ...
Hello everyone!One of our end customers noticed the following log messages appearing multiple times on his N7K running version 6.0(4):%MTM-SLOT8-2-MULTICAST_SOURCE_MAC_LEARNT: Inserted dynamically learnt multicast source mac [MAC_ADDRESS] Please exe...
Hi Everyone, We have 2811 configured with PIM. interface FastEthernet0/0 description outside ip address 10.225.30.50 255.255.255.0 ip pim sparse-mode ip nat outside ip virtual-reassembly zone-member security out-zone duplex auto speed auto!interfac...
Hello All, Switch to Configure: Cisco 3560G, 48-Port POE I have this older switch at my desk that I want to use for testing and configuring devices, like IP Phones, Access Points, etc... This switch is no longer used in our production network, so ...
I have 3 sites, 1 HQ site with a static IP and 2 remote sites with dynamic IPs. Each site has 4 separate networks, all with the same address spaces. For security reasons, I only want 1 to have internet access. Site one network 1 VLAN 10, IP 10.10.0....
I have a Cisco 1921 router with two GE interfaces running IOS c1900-universalk9-mz.SPA.155-3.M.bin. I also have IP Base and Security packages installed. According to Websense and Cisco docs, I need to use the following command to specify url filteri...
Hi: I have a Cat 2960X connected to a Cat 2950. The connection is copper Gbic to SFP. The connections works for days and then just stops working. I have to reload the Cat 2960X to get the communicating. Any Ideas? Note: Cat 2960X interface confi...
Hi im fairly new and about to sit for my CCENT exam soon. i still confuse on a few set up of Network equipment. if ISP provide static ip for a company, how and where do you set the Static IP to, from this kind of setup:- 1) ISP Modem ----> Firewall ...
Hi Everyone, I have a pair of Nexus 5548up in VPC mode also doing layer 3 routing between some vlans. I have an active/standby setup for my ASA firewalls. What is the appropriate method for routing traffic from the Nexus over the the ASA. Do I n...
Hi, I have a 3850 switch (running 03.03.05SE) operating as WLC but it doesn´t take any configuration related to a SSID. After a power failure it set the SSID to default configuration and I can´t reconfigure it (web or CLI). I tried to create a new ...
Hello, if you have a streaming server sending out multicast traffic to a pre-defined multicast address, do you need to configure the nearest facing router to receive this traffic, or does it just come in to the router interface by default ? I am aski...
My Collegue has a strange issue and i don't understand what happened. I have a PC in DHCP and when i try to ping an host that is on the same Switch works fine, But if i configure that PC with static Address and try to png that host i receive Host Unr...
If I have 4 switches configures as a stack - where StackWise ports are connected as 1 to 2, 2 to 3, 3 to 4 and 4 to 1. Switch1 is the master. If something were to break stack connectivity between 4 to 1 stack still works as Switch 4 still has connec...
Hi, I have a very high utilization on one of my 2960 port! this port is connected to my hp server. I got this server when my server is not booting with os. show interface gi1/0/15 GigabitEthernet1/0/15 is up, line protocol is up (connected) Hardwa...
I have set up a Cisco 871 router but I am only using it as a switch. I have int fa1 as an access port for vlan 801 and int fa2 for vlan 802. I have int fa3 set up as trunk to my Cisco 2821 router. Fa4, the WAN port is not connected. I have one host c...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
11-08-2024 02:07 AM | ||
11-06-2024 04:49 AM | ||
11-04-2024 07:57 AM | ||
10-25-2024 03:21 AM | ||
10-24-2024 11:57 PM |
User | Count |
---|---|
16 | |
9 | |
6 | |
5 | |
5 |