Dear All, I am running into an issue with an old IOS and EEM script as I can't make it bypass the AAA. So I have a script that should log into config mode and shut an interface if an event happens. Writing the script is not an issue. But to make ...
Hello, we are building a project and we have to choose different switches and routers from Cisco, to wire a 4-storey building (ground floor + floor 1 to 3). Each floor has 20 rooms, each with ten computers. On each floor, ...
We are replacing our mixed seven device L3 Core with two 6800's in VSS. I'm currently learning to configure VSS but I'm not sure if I need to do anything specific on both 6800 switches before enabling VSS, there seems little information on this. For ...
i was doing some hands-on labs and typed in "boot system tftp c2600-i-mz.123-9" to boot my router from a tftp server and when my router restarted it said that the file was to large to load into memory and my router kept restarting at that point as it...
Hi All, I have multiple project with dedicated internet Service provider, Right now i have prefix subnet routing toward ISP for project. I can apply route map on router instant of static route.Please share configuration or option to achieve. Router...
I have two router R1 and R2, ibgp R2: interface Loopback0 ip address 2.2.2.2 255.255.255.0 interface Lo1 ip address 22.22.22.22 255.255.255.0 !interface FastEthernet0/0 ip address 155.1.12.2 255.255.255.0 no shut! router bgp 1 network 0.0.0.0 mask 25...
hi out there I have a setup vhere I need to open og close a vasi interface based on the occurence of a route in a vrf - can I track a route and then use a script to shut or no shut a particular interface if this route shows up?
WIC2T card does not recognize in c1941 router. Why it doesn't work normally?If is it related HWIC? Please reply my question T_T
Hi all, I have a doubt. Can you help me please? Is it possible to configure Private VLANs on Catalyst 2960-X series switches? . I refer to Private VLANs like the concept of promiscuous and isolated ports into the same VLAN. The communication not is ...
Hi, Consider the picture Attached I want to make Inter VLAN between to switches using a Router. when trying to use subinterfaces using this CLI command: interface FastEthernet0/0.1 encapsulation dot1Q 10 ip address 10.0.0.1 255.0.0.0 interface FastE...
We have several end user Catalyst 6513 switches (non E series) that are maxed out with 6X48 series blades. We noticed they are end of support next summer. What is the logical successor for them? 6800 series? Thanks! Jeff
Is there a command similar to "test etherchannel load-balance int port-channel # ip 1.1.1.1 2.2.2.2" (available on the 3750 switches) for 3850 switches. I cannot find a way to test which interface of a port channel a particular flow will use.
what is impact of this bug.....
Dear Cisco Support, Is there any way to track/monitor interface on switch "WS-C2960S-48TS-S" "ex gi1/0"so that if it goes down to link it with other interface "ex gi 1/1" to force it down for HA purpose. Best Regards
Hi Guys, I'm having an issue figuring out how to plug a physical device in a virtual design. I'm trying to plug a webfilter inline between my switch and firewall so it can filter traffic transparently. The problem is that my firewall is virtual run...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM | ||
| 05-23-2025 10:30 AM |
| User | Count |
|---|---|
| 11 | |
| 9 | |
| 8 | |
| 5 | |
| 5 |
