I have read that CAT6 can also provide 10G speed but upto a limited distance. Is this right ?? Please share any relevant link and information. Regards, BL
I have read that CAT6 can also provide 10G speed but upto a limited distance. Is this right ?? Please share any relevant link and information. Regards, BL
Hi we using the following topology 1- 2 x N9396TX vPC 2- 2 x C6800 VSS 3- HP blade system C7000 and virtual connect SW (virtualized environment using ESXi 5.5) 4- Cisco CUCM server that have ESXi in vlan 1 (native) and other VMs (Voice VMs) in vlan 1...
Hello,I'm worried about the configuration of QoS on a Catalyst 4500 and C2960.could you help me on the configuration trunk interface between catalyst and 4500 and PABX and between 4500 and 2960 switch.thank you in advance
I have a client latop (192.168.0.3) which connects to a Cisco router (R1) on interface fe0/0, address 192.168.0.12. This router has an SVI (vlan 10, 192.168.10.254). Interface FE0/1 has vlan 10 assiged. FE0/1 then connects physically and directly to ...
So, short summary. During a password recovery, the config.text file was renamed with no name, which then sent it to a new dir called lost+found. This directory was renamed config.text so the file would be found at flash:config.text: yet with no...
Ok. So I have a N6004 with a N6004x-M20up card installed in slot 7. Int eth7/1 is directly connected to my laptop (via copper of course just to be clear). I cannot get the int up/up. Image used was n6000-uk9.7.1.1.N1.1.bin I have tried: Shutting the...
Hello All, We've bought x10 new WS-C2960X-24TD-L and bump into a strange problem that we can't change the hardware clock to be accurate with software clock. Thanks for your solution. Switch Ports Model SW Version SW Image ------ ----- ----- --------...
I have a CISCO SGE2010P 48 Port 10/100/1000 Ethernet switch with POE. The SGE is used as our core switch. I came into work and everything was down. When I pinged the switch there were intermittent replies approximately 5 replies every 30 seconds. I w...
Does the nexus 5020 support 1Gb sfp?
I am currently using two Catalyst 6500 switches on my network. I am in the process of implementing VSS between the two switches. I currently have HSRP groups configured on all Vlans on the switches to manage traffic on the network. My question is do ...
Hi I apolgize in advane if these questions are extremely easy Im still a beginner. If the Cisco 3850 switch has a 115V/12A power supply, We have 3 of the switches if we go with(it’s called 208 power I think(the big round connectors)) 208V/30A power...
Everyone I have a pair of nexus 7010 and I have aaa working and i am using Active directory for user authentication. But when a user needs to change there password they do not get prompted???? am i forgetting somethingI have the aaa-new-modelandaaa...
Hi All, Getting an CRC errors on all ports slot 3 line card 10/100BaseTX (RJ45)V. IOS: cat4500-ipbasek9-mz.122-31.SGA9.bin Did an RMA but also issue not resolved. FastEthernet3/5 is up, line protocol is up (connected) 96232 input errors, 7986 ...
Hello, When using ip route <network><mask> interface <interface> how does IOS determine the destination MAC to use when encapsulating the datagram? Oviously on a serial link there is only one destination. However if a broadcasting protocol like eth...
In an all-Cisco MST environment, will "spanning-tree mst forward-time XXX" affect the speed of the fast switch-to-switch handshake? Or only affect edge ports (how many seconds to wait, when there is no fast handshake)? I'd like to slow-down the han...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-19-2024 05:58 AM | ||
04-19-2024 02:04 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
12 | |
10 | |
8 | |
7 | |
7 |