Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

I have a pair of 4451-X routers (XE 3S) running MHSRP on a "nat inside" interface - each is active for its own group and standby for the other's group.Each router has two "nat outside" interfaces each running a single HSRP group, and one of the route...

Hi fellow forum members. In one of my networks I use etherchannel between my access layer (mainly 3750s) and distribution layer (6500).  Right now I am using a load-balance method of src-mac, and I'd like to switch to src-dst-ip. When I make the chan...

Please help me!! I am working on a Catalyst 3560 IOS 15.0(2) SE I have my switch with a couple of  VLANs and routing enabled, but my switch doesn't seem to route... Desription: VLAN 10VLAN interface 10.190.1.3/24 VLAN 20VLAN interface 192.168.20.1/24...

    I have a Cisco 4506 switch and its 10 gig interface is in error disable mode.I tried Shut and no shut the port couple of times but it transits from up to down number of times and then to error-disable. Did anyone else encountered this issue befor...

I have two networks. 10.22.227.X the 227 network has the internet connection on it, I also have 10.22.226.X Network as of right now this network has no internet.You can see the current configuration file here http://jpst.it/yTurAs of right now i can ...

Hi,I am designing a small data center with ASA5512-IPS firewall.The configuration is like: ISP--->2921 Router--->5512 Firewall--->4503 Core--->2960 AccessI am confused about connecting firewall in routed or transparent mode. Will transparent mode wor...

Hi guys - I have a network setup that I'm a bit confused about - it has to do with packet forwarding over a routed link.Here's the scenario:TopologyR1 (Gi2/17 IP:192.168.74.129/30) <------------> R2 (Gi2/1/1 IP:192.168.74.130/30)# Routed link between...

Resolved! IPSec overhead

Hi AllI need some help trying to figure out the IPsec overhead in ESP Tunnel mode.Scanning the internet makes me believe the overhead must be between 51 - 58 bytesWhen testing this in Wireshark makes my head spin.R1 --- R2 --- R3-- R4  (IPsec tunnel ...

Bruin2781 by Level 1
  • 3239 Views
  • 4 replies
  • 0 Helpful votes

I'm running a 3725 with Cisco IOS Software, 3700 Software (C3725-IPBASE-M), Version 12.4(25d), RELEASE SOFTWARE (fc1) Cisco 3725 (R7000) processor (revision 0.1) with 244736K/17408K bytes of memory. R7000 CPU at 240MHz, Implementation 39, Rev 3.3, ...

I just found out Cisco has introduced support for RFC 1687 in IOS 15.2(2) however I cannot find ANY ssh client implementations that support it. As I am working on a major project to revamp and secure my organizations router and switch authentication ...

I'm trying to configure contexts for various VRF's in a router (specifically testing on a 2811 running IOS 15.1.4).  My understanding is that for SNMPv2c, the contexts should be available by polling the device with <community>@<context>, confirmed by...

Resolved! OSPF-4-NOVALIDKEY

I have a cisco router   isr4300 runningCisco IOS XE Software, Version 03.13.02.S - Extended Support ReleaseCisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.4(3)S2, RELEASE SOFTWARE (fc3)getting this error on all interfac...

mabeita by Level 1
  • 5345 Views
  • 1 replies
  • 0 Helpful votes