Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

I have a cisco 1700 router that I would like to connect to my Verizon Actiontec router and the actiontec is 192.168.1.1 how would I be able to access the internet? I do have an 4 port hwic card.

moman1962 by Level 1
  • 275 Views
  • 1 replies
  • 0 Helpful votes

Hello, I have a switch-C960X version 15.0 (2r) EX, and I was looking at the securit config guide for 15.0(2) EX.There's suppose to be a command to force a port to re-authenticate itself as I'm trouble shooting 802.1X issues. The command is "dot1x re-...

dcanady55 by Level 1
  • 146 Views
  • 0 replies
  • 0 Helpful votes

Hi, I'm installing switches for a client located very far from our HQ. This client is only accessible by plane (it is actually a mine located nothern Quebec, about 1000 km from our office).  I was about to finish the configuration of the switches whe...

Hello I have (2) Cisco 4500x with a VSS config. I als have a couple cables "SFP-H10GB-CU1M".I want to make sure I have this physically setup correctly. I have searched but not found anything specific enough.Please review and advise.  

Is there document/procedure for replacing the 5010 Pair with 5548 pair?  From what I understand the VPC's are compatible between a 50XX and 55XX hardware due to a change in the ASIC, is this correct?  Has anyone completed this type of upgrade? Thanks...

joeharb by Level 5
  • 150 Views
  • 0 replies
  • 0 Helpful votes

HI,We have Cisco 4500X at the core and Cisco 3750 at the edge. I would like it so we can disable unmanaged switches on some ports on an edge switch. I don't want a particular group of users plugging them in.How can i achieve this please?Thanks

I am setting up a stack of three WS-C3650-48FD.  Software version 3.3.3SE and Image version cat3k_caa-universalk9.  When I apply the following route map: route-map STATIC-2-EIGRP permit 40 match tag 400 set tag 400 I get the following message: Erro...

andym5041 by Level 1
  • 617 Views
  • 1 replies
  • 0 Helpful votes

Dear Friends, We can find the high CPU utilization on our l2 catOS 4506 switch, we are hitting with the syslog as "Invalid traffic from multicast source address 08:00:01:02:00:00 on port 1/1" Does this syslog message relates to the high CPU ?? Kindly...

We have two 6500E switches and running spanning tree with rapid-pvst.We have also configured per vlan spanning tree priority with 100,200 so odd vlan have one switch hight priority and even vlans have  another switch high priority.I have created new ...

datamodule by Level 1
  • 5013 Views
  • 12 replies
  • 0 Helpful votes

Description of the problem: I see that the router reloaded due to software crash. i want to understand the reason for this crash. CHN_TAO_BRA_AR02#sh ver Cisco IOS Software, 2800 Software (C2800NM-ENTSERVICES-M), Version 12.4(3d), RELEASE SOFTWARE...

Hello. I would like to configure my C2911 router with 2 C2960 switch. And is it possible to put same ip on 2 interfaces of C2911? One for active and another one or standby. Topology was attached. Is it possible? thankyou

Resolved! Stack ports

Dear, Can I use the Stack ports between 2 3750 switches as a connection between them, where I want to configure a RSTP redundancy using those ports. Thank you for your help.

I have 2 systems in different locations sending to the multicast address 239.192.201.19 on port 55304 - I have been tasked with sending both of these feeds into another system for analysis.  So immediately you can see the problem. After some googlein...

Dan Smith by Level 1
  • 1590 Views
  • 0 replies
  • 0 Helpful votes