HiOn a 3750 I have configure a new vlan 114 and assigned it the adress 192.168.114.254, I've put my port in trunk mode with with the other vlan wich is vlan 1 192.168.14.254. I would like for both network to ping each other, when I received a adress...
Hi everyone,In the Cisco documentation, says thatYou must configure the same virtual switch domain number on both switches of the VSS. The virtual switch domain is a number between 1 and 255, and must be unique for each VSS in your network.My doubt i...
Hello, I have a 4510E iand a 3750 with 4 stacked switches in a lab environment . On the 4510, I have g1/48 configured as switch mode access port and switch access vlan 182. On the 3750, I have port Fa1/17 configured the same way. I rebooted the 451...
I would like to setup an MD5 passwords under the VTY, CON, and AUX line ports but the IOS (c2951-universalk9-mz.SPA.151-4.M1.bin) only let's me setup a "7" hidden password. Is there anyway to do this?
Hello all. I installed a RPS2300 with a switch WS-C3560E-24TD and work temperature in switch up to 40 º C and 43 º C. Anyone know if this work temperature is normal? or extremely high. Thanks
Hi All,( R ) ------ [ 3750 ] ------- [ 2960 A ] |------------ [ 2960 B ]I had these VLAN on the 3750 & 2960:- Vlan 8 (mgnt Vlan), Vlan 17, Vlan 34, Vlan 35Basically I had already configure switchport protected on all the port o...
Hello. I am having some troubles with my CISCO PIX 501 configuration.Since a few month ago I started to get random disconnections on my network (from inside to outside). The machines can ping the DC or the Pix but cannot surf over the internet. The o...
Hi,full mesh is recommended in several network design guides also when not using VSS/VPC.E.g. Cisco Borderless Campus 1.0 Design Guide and Enterprise Campus 3.0 Architecture Guide:"As a general best practice to build resilient network designs, it is ...
Hello everyone,I've recently found that one of the switches on my network (which I never set up) is running a "no spanning-tree vlan 3, 5, 10" command, which I want to remove, but I have been unable to. When I do try and type in "spanning-tree vlan 3...
Hi all,After lot of research, I'm not able to find a command that allow me to limit to a specific bandwidth an interface on a Cisco 3650 IOS XE.The bandwidth limit has to be applied every time, not just during congestion moment. So I think I cannot u...
The issue is DSCP is preserved from SiteA to SiteB whereas DSCP marking is not preseved from SiteB to SiteA. (Site A) Phone----Cisco 3560 SW----Cisco 1921 Router========(Bonded T1)=========Cisco 1921 Router-----Cisco 2960 SQ---Phone (Site B)Site A C...
Hello guys, I have a L3 port-channel between 2 gigabit ethernet interfaces (one per switch Catalyst 6509), towards two giga interfaces in another two Catalyst 6509 in the other end. The port-channel is configured as follows in one of the ends (the fi...
Hi all, I was viewing VSS configuration in latest 4500 switch configuration guidehttp://www.cisco.com/en/US/docs/switches/lan/catalyst4500/XE3.5.0E/15.21E/configuration/guide/vss.html#wp1053927Under pre requisite, it says that SUP 7E and 7LE are supp...
we are using Cisco CISCO1921/K9 (revision 1.0) with 2 Gigabit Ethernet interfaces, we want to expand the LAN connectivity, can i add Gigabyte module to the existing.? Thanks in Advance.
I'm having a problem with speed/duplex settings with the Nexus 1000v. I recently upgraded the VSM and VEMs to version 4.2(1)SV2(2.1a) with the VMware hosts on ESXi 5.1. We're now trying to bring an ESXi 5.5 host into the Nexus 1000v and when migrat...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-26-2024 04:58 AM | ||
| 11-25-2024 07:00 PM | ||
| 11-20-2024 10:11 AM | ||
| 11-17-2024 06:34 PM | ||
| 11-06-2024 04:49 AM |
| User | Count |
|---|---|
| 9 | |
| 8 | |
| 6 | |
| 6 | |
| 2 |
