Buy or Renew
Buy or Renew

Switching

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

DHCP service over single interface

Hello,Is it possible for my Catalyst 2960-s to provide DHCP/NAT service over a single interface? There is no other DHCP server on the network. I am thinking there must be a way to do this, maybe with a VLAN to a specific interface on the switch? I wa...

joetholen by • Beginner
  • 319 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Cisco Catalyst 2960-X Series

Hi!I was checking the specs for the Cisco Catalyst 2960-X Series but could not identify the number of Total switched virtual interfaces (SVIs).What is the number of SVIs on the WS-C2960XR-24TD-I model?Regards,Alvin

net buzz by • Beginner
  • 692 Views
  • 2 replies
  • 0 Helpful votes

MACsec between 2 x Nexus 7K M2 ports

Hi,I am trying to configure MACsec between three Nexus M2 ports.  once I configure it, my BGP and ISIS neighbors go down.here is the output of my show cts interface all on one of the switches:CTS Information for Interface Ethernet1/1:CTS is enabled, ...

CiscoNutt by • Beginner
  • 515 Views
  • 0 replies
  • 0 Helpful votes

eigrp FD

Hi i have attached the topology of my network. I am running eigrp. My question is, access switch a seems to load balancing between links to 3750_A and 3750_B to reach the outside world whereas it should only go through 3750_B since it has 1 gb link, ...

Resolved! Changing cores from HP to Cisco

I have a site that my company taken over.  It has two HP 5406's being used as cores, with a hodgepodge of HP2510 and other model switches being used as access switches.  All the VLANS are terminated on the 5406, using VRRP, with the access switches t...

Cisco 3750 DHCP and Routing Errors

Hi All,I have encounted an problem that currently has me stumped. I am trying to configure a 3750 switch with ipservices for use as a small localised test bed for wireless. what i am planning to implement is:1 x 3750 PoE switch with 3 vlans1 x WLC1 x...

lukedp by • Beginner
  • 294 Views
  • 1 replies
  • 0 Helpful votes

Routing problem, loop, static route.

HiI`m suddenly having problems with some static routes on a WS-C3750G-12S-E running 12.2(44)SE5.The routing table is really simple, only some static routes and a couple of VRFs. Gateway of last resort is 10.0.224.29 to network 0.0.0.0 10.0.0.0/16 is ...

perpaal by • Beginner
  • 1858 Views
  • 6 replies
  • 0 Helpful votes

Resolved! 2960S Stack password recovery

Hi,What's the method to perform password recover on a stack? I aleady have the standard procedure/link to perform on a single switch. Do I power down both members, disconnect the stack cables, then perform the procedure on the master, then power back...

lcaruso by • Frequent Contributor
  • 2379 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Router not issuing IP's

Hello all,Newbie here and have been working on configuring a router and not having any luck getting ip's from it.Any help will greatly be appreciated....Current configuration : 3990 bytes!! Last configuration change at 01:06:48 PCTime Thu Aug 29 2013...

rrealy by • Beginner
  • 603 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Why does Catalyst 2960-C switch keep rebooting

We just bought a 2960-C PD 8PT switch.The switch is delivered without powersupply. It is supposed to get power from a PoE port on another switch.When I connect the Gigabit 1 or 2 port on the 2960-C to a PoE port on my 4507 switch the 2960-C switch st...

torleif by • Beginner
  • 4671 Views
  • 3 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers
Spotlight Award Nomination