Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

 
Labels

Forum Posts

Hello Guys,Anybody could explain how did you installed the 6500 VSS process with dual sup 720 per chassis (VSSo4 - 2 Sups with 1 chassis)? Do we need to do anything extra or is it the same as single Sup VSS process? I am going for such a scenario, bu...

jbnair by Beginner
  • 848 Views
  • 4 replies
  • 0 Helpful votes

Hi,Hopefully someone has come across this problem before...The testing topology looks like this:10.250.2.50 (VLAN 2502) -----> Nexus 2K -----> Nexus 5KA (SVI 2501, 2502) --------> Nexus 2K ------> 10.250.1.50 (VLAN 2501) LAPTOP A                     ...

zykobot by Beginner
  • 871 Views
  • 2 replies
  • 0 Helpful votes

Hi,I am looking for a wireless router that supports clustering, Gigabit Switch (4 or 8 ports) and firewall. I have been looking at SRP541W, which seems to support them all except for wifi clustering.So, basically i am looking for a device similar to ...

janlunddk by Beginner
  • 733 Views
  • 1 replies
  • 0 Helpful votes

As far as the end-of-life notice for Cisco WS-C3560G-24TS-E goes, it shoud be replaced by WS-C3560X-24T-S.Where can the differences between these models be found ?To be more specific, I'm interested in the evolution for - the number of HSRP instances...

p.devalck by Beginner
  • 430 Views
  • 0 replies
  • 0 Helpful votes

HiI have a Cisco 881 router when enter show ip cache flow, I see this:SrcIf         SrcIPaddress    DstIf         DstIPaddress    Pr SrcP DstP  Pkts..Fa4           M.M.M.M   Local         X.X.X.X 32 D090 FC43    13K..Is a large amount of packets. The...

I'll try to keep this simple for my initial question.   I am dual homed for my Internet service.  I have two ASA firewalls pointed, one each, to the two Internet links.  Both these firewall internal interfaces reside on VLAN5.  Lets just call them AS...

hhorton by Beginner
  • 899 Views
  • 6 replies
  • 0 Helpful votes

                   Hi Everyone,Router has below ACL  configuredaccess-list 106 permit 0.0.0.0.27 255.255.255.224 host 200.x.x.x.xNeed to know which IP address will this ACL allow?Regards Mahesh

mahesh18 by Frequent Contributor
  • 506 Views
  • 2 replies
  • 0 Helpful votes

Hi,i'm desperately trying to get LACP working over a dot1q Tunnel.The "Service Provider" Switches are two 4506-E Switches with SUP7-E connected via a 10G Link, running on cat4500e-universalk9.SPA.03.03.00.SG.151-1.SGsample config:dot1q tag vlan nativ...

FH STP by Beginner
  • 6608 Views
  • 5 replies
  • 0 Helpful votes

All,I'm not sure how to go about troubleshooting this one. I have a site that has pim dense enabled. I had to do this for some local multicast traffic they needed to support, but I did it for all of our sites. The other sites have normal looking mul...

What is causing this and how do I fix?I corrected by rebooting the router. My VPN stopped working during this.After the boot it was good.thanks,                   sa live is 86400 by the way.I have the latest firmware too.

Hi,Iam planning to change the configured area type of existing core switch (L3-4507) from stub to normal area. As our environment is not too big (3locations) I do not see a need for this area to be stub and also I need to add extranet connection at t...

mvsheik123 by Rising star
  • 330 Views
  • 2 replies
  • 0 Helpful votes

Hi all, I was ask this question in an interview. 40G max length is 100-150m. What if we need to provide 40G between 2 endpoints that are 600m apart ?Kindly tell me what is the approach ?

Jonn cos by Enthusiast
  • 237 Views
  • 3 replies
  • 0 Helpful votes