Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Ok so I believe I have done everything right so any help would be greatly appreciated. Attached is my running config. I have the et0/0 set up for dhcp because it's connected to the outside network, the switch interface connected to vlan 2 which has a...

jcclubb15 by Level 1
  • 574 Views
  • 3 replies
  • 0 Helpful votes

Hello all,I have a setup of a ASA 5550 connecting to a Cisco 3560 where the port on the ASA is configured to 192.168.1.2 255.255.255.0  and the port on the 3560 is configured as :      interface GigabitEthernet0/23description **Cisco ASA**switchport ...

                   Hi, I'm quite new to the networking work. I'm an Audio Visual Tech so I don't touch much of this stuff.I have a LAN Network I'm setting up at my house. I had a little bit of trouble, thought I might run this by you guys and see if ...

I have a remote site that's just installed a Cataylst 3560 v2 which I need to configure. I'm guessing the default username and password are both cisco; however, web GUI and Configuration Assistant won't let me in - both are asking for realm level_15_...

In the past, switches used either cut-through or store-and-forward switching as the forwarding methods to switch data between network ports.  Although store-and-forwad is the sole forwarding method usedtoday on Cisco Catalyst switches, was there ever...

I have 2 Catalyst 3560x switches each with 4 Gbic uplink modules.  What I would like to do is connect 3 of the modules on one switch to 3 modules on the other switch to create a 3 Gb channel.Please note that while I am pretty computer savvy, I know n...

hi guys, I have encounter one problem about C4507R. when 4507's cpu is high ,the hsrp cutover. then customer complain the internet is disconect. So I want to config copp on 4507. but I don't know how to do it. Because it is one production network. Wh...

Tom Yan by Level 1
  • 635 Views
  • 1 replies
  • 0 Helpful votes

Dear Folkz,I've 2911 router and whenever i trying to take telent of this router , i'm not getting the telnet prompt at all but thru ssh i'm able to login this router.We've confgured the telent paameters as below.line vty 0 4 exec-timeout 5 0 privileg...

We have had a rash of problems with rogue DHCP servers of late so its time to bite the bullet and enable snooping. Problem is I cant get it to work.With it enabled the test phone cant get an IP from the production DHCP server but rather it will only ...

Hello Experts,I need your opinion on this scenario where one ESX host has two LAN cards connected to L2 Switch. In this, will the traffic use both links or one would be blocked due to STP and if yes then do I need to configure port channel on switch ...

ray_stone by Level 1
  • 311 Views
  • 4 replies
  • 0 Helpful votes

   Hi allI am trying to upgarde a dual stack core switches IOS and I am getting the following errorsDirectory of flash:/    2  -rwx       30852   Mar 6 2013 12:58:16 +00:00  ArchiveMar--6-12-58-16.404-15    3  -rwx       30916   Mar 6 2013 15:11:24 +...

Resolved! NATING

Hi,I am sharing the topology Picture and cofiguration file in attachment. Both PCs (PC0 and PC1) are unable to ping each other. Please check configuration of routers and solve the problem.

Dears , I have 2 6500 switches both with same image s72033-adventerprisek9_wan-mz.122-33.SXH7.bin but hardware is different cisco WS-C6509 (R7000) with WS-SUP720-3B and cisco WS-C6509-NEB-A (R7000) Is it possible for me to configure VSS on these boxe...

Haris P by Level 4
  • 442 Views
  • 2 replies
  • 0 Helpful votes