Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Dear all,Please provide help to make design of FTTH in campus network.waiting for response.regards,
Hi allI have a new link I want to bring into my network, But I dont want OSPF neighbours to be formed on the link as it will most certianly be used as its a lower cost.How would I achieve this ?Would I just use the passive interface command? or just ...
How to confiure internal VLAN ip routing?
Hi,We have a Nx5548up pair connected to FI6248 via a vPC. We had to reboot a FI (in order to configure more FC ports) ; following that reboot, we meet many issues.The first log shows the vPC down showing the FI rebbot.2013 May 23 12:31:45 sw-n5kup-fr...
Hi all: I need help how to recover password and retrive configuration on Cisco switch 2950 and 3560. I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything...
I have a Cisco Router C3900.the interface Embedded-Service-Engin 0/0 is administratively is down.But when the router reboot, the router check the interface and since it's down, it does send an alarm (SNMP trap).Does anyone know how...
Hi All,I have in logs following error message , could you please explain what is reason %DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module 1 has failed test SpineControlBus 20 times on device Power Mgmt Bus on slot 10 due to error Spine control test failed err...
Hi,i have a 3750 switch and i wish to use IP SLA. i am running c3750-ipservices-mz.122-25.SEE2 which does not work. Does anyone know what version i can use to enable this feature.cheerstony
hi , i just want to ask ,if i configured subinterface on router , lets say ==>gi0/0.10 and i put encapsulation dot1q 10does that mean , that the traffic goining out the interface gi0/0.10 will be tagged with vlan 10 ??i want to make sure , does the...
Hi all on my lab I have a cisco 876 with, c870-adventerprisek9-mz.124-6.T9.bin.I have configured a VLAN with ID 230, an SVI with IP 192.168.230.1/24 and I have assigned switch port fa 2 to it…interface Vlan230 ip address 192.168.230.1 255.255.255.0 ...
Hi,we have several Linksys SRW switches in our infrastructure. In this case I have a port on a SRW 2048 wich I want to join into a VLAN I created on the switch. The client is not able to handle VLAN IDs. Also, I want the port to only comunicate with ...
I have an MPLS network router(Router1) and an internet router(Internet1) at a site of mine(Site1). the MPLS router sends all unknown traffic out the internet router. Router1 is the default gateway for all hosts and directs the traffic. I also have an...
Hi Everyone,I have 3 routers R1 R2 and R3 .All are EIGRP neis on AS 123.R1 config router eigrp 123redistribute connectedpassive-interface defaultno passive-interface FastEthernet1/0/1no passive-interface FastEthernet1/0/3distribute-list 9 outno auto...
Hello,I don't have a power-stack configure on my stack and I'm getting this warning on my switch after upgrading to new IOS version 15.0(2)SE2 (WS-C3750X-48P-L).PLATFORM_STACKPOWER-4-REDUNDANCY_LOSS: Switch 5's power stack lost redundancy and is now ...
Hopefully this is the right spot, I'm a bit green to some of the routing and VLAN configuration and I cant seem to find settings that do what I want.I have a netgear FS728TP configured with 2 VLANs. The primary untagged vlan 1 is data and goes out ou...
