Hello,I want to upgrade my DRAM of 256MB to 512MB to support 15.1 IOS image.Can I buy Cisco approved DRAM from third partyLike www.satech.com Pls let me know. ThanksK
Hello,I want to upgrade my DRAM of 256MB to 512MB to support 15.1 IOS image.Can I buy Cisco approved DRAM from third partyLike www.satech.com Pls let me know. ThanksK
hi,a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?portfast an dother parameters are...
Hello, colleagues. Ive got a 494810ge switch, and this parameters are important for me:sh int gi 1/4 counters detail Port InBytes InUcastPkts InMcastPkts InBcastPkts Gi1/4 252819467437788 173264735013 ...
Hi all,I have a stack of 4*3750 switches with 52 ports each (48 + 4). Is it possible to have port channels above 48th one in the stack in any way? Thanks and Regards,Balachandhar S
hi ,I have a Query on OSPF .i am running two P2P links between two sites with two Cisco 4506E switches running with HSRP at both ends . both P2P links with same bandwidth from Different ISP. is it possible to Load balance for this Two links .please...
Hi all,Does the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are comp...
Hello - I'm looking to do a basic QOS configuration which states that VOIP traffic has priority over anything else.Can anyone lend a hand?
Can not set route map on interface vlan. which in non default vrf on Cisco 3750.IOS c3750-ipservicesk9-mz.122-55.SE.binsdm prefer route in enableip vrf users rd 200:0 route-target export 200:0 route-target import 200:0interface Vlan201 description Us...
Hi,I'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 ...
I am running into a DHCP problem on a Cisco 891 running 15.0(1)M2. I am running DHCP on the router and want to reserve an address for a printer. I have done this hundreds of times on hundreds of routers. Per Cisco recommendation, I let the printer...
While configuring PoE Ethernet EHWIC PoE modules with ISR G2 routers Cisco DCT gives a warning to select AC Power Supply with PoE ‘PWR-3900-POE’. Do we need to select the PoE power supply for Enhanced EtherSwitch SM PoE modules also (at present it do...
can any one explain me the below snmp traps meaningsnmp-server enable traps ttysnmp-server enable traps cpu thresholdsnmp-server enable traps configsnmp-server enable traps bridge newroot topologychangesnmp-server enable traps syslogand which are the...
I want to know if WS-C4506-E able to perform DHCP?
Hi,I would like to check if it may be possible to hot-upgrade/swap the 4506E power supplies? Based on the configuraton guide; I have summarized the steps as follows:1. Switch has 2 existing power supplies to be upgraded2. Remove right side/bay 2 powe...
Hi everybody.I am getting a little different result than expected in the following example.|--------f0/0--R1-----s0/0-------------------R2R1 config :f0/0 10.10.10.1/8s0/0 199.199.199.1/24eigrp 1network 10.0.0.0network 199.199.199.0When R1 sends up...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-05-2024 02:17 AM | ||
09-05-2024 01:32 AM | ||
09-03-2024 09:19 AM | ||
09-03-2024 06:59 AM |
User | Count |
---|---|
7 | |
6 | |
6 | |
5 | |
5 |