Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Hello, Good Afternoon. I would like to ask if what is the maximum concurrent that a CISCO1941-SEC/K9 could handle. The scenario is that on a lending company running SQL 2008 R2 and other applications, 50 to 100 branches using RV042G will connect t...
Hello,I am trying to have F4 (the WAN interface) bridged to a VLAN interface. I have put my VLAN interface and my F4 in the same bridge-group, set an IP in the BVI Interface, and made sure that VLAN was properly trunked and configured on one of the r...
hello,we have four switch-es.Two 2960S-24TS (1. and 2.) and two 2960G-24TC (3. and 4.).I want to connect them to have best performance and redudancy.Can I connect them on this way (mesh network):1. 2960S (1.) - 2960S (2.) with two Fibre cables (two...
Have the following designAS we have below the phne connects to the 3750-A access layer switch (VTP mode client) which connects to the nexus 5596 (The nexus is the layer 3 device and set to vtp mode server) and finally we have a Voice recorder that ...
Hi all,I have an issue with my setup of a 6500 switch (12.2(33)SXI9). We have a 6500 switch with several VRF's. For a certain VRF I would like to redistribute a static route in EIGRP. After doing so I don't see the static route on my eigrp neighbor. ...
Is there such a thing as too many broadcasts? I have a Cisco 2960-24TT-L switch with two devices that need to exchange about 90Mbps in broadcast traffic (each device sends roughly 48,000 235-byte broadcast frames each second). It seems like the bro...
Dear All,In my ongoing project i need to monitor cisco 3750-X port status (uplink/downlink)i.e. whenever there is some problem at a specific port.I need to monitor it through an OPC server and right now what i am doing is as follows:i am using Kepser...
Hallo,i am an automation engineer, and in my recent project i need to monitor cisco 3750-X port status (uplink/downlink)i.e. whenever there is some problem at a specific port.I need to monitor it through an OPC server and right now what i am doing is...
hi,We are using WS-C3560G-48PS connected via UPS power supply. Whenever raw power supply gets fluctuates few of the IP phones (Alcatel) gets reset although switch is remain up and running. We checked the same by disconnecting the raw power supply but...
I am relocating UPS units and will need to buy longer power cables to extend from our 4506 and 4510 to the new location.I think I am looking at 15 to 20 feet but I am going to confirm. Is it okay to use longer cables? Thank you.
Currently Being Moderatedpassword recovery helpsome bady can help me with password recovery switch 2960that what i am doing and i get faill sll the time what i am doing worng? switch: flash_initInitializing Flash...flashfs[0]: 0 files, 1 directoriesf...
Hi all, I just spent 3 hours with TAC getting no where, but my problem seems simple.Topology is below.Each host has a primary VLAN (V1 and V2) with a default GW towards the Nexus, and a common VLAN (V3) between them---- V1 |----| V2 ---- | A |----| ...
I have a C3560-24P PoE switch, running on a very small network with nothing special about the endpoints or the configuration (5 laptops connecting via 1 wireless AP, 1 firewall uplink, a networked printer and one conference room phone using PoE. Th...
All, Are there any considerations to make for connecting newer IOS devices to older CatOS?Summary:6509 switch with CatOS 8.7, policer values shaping 20M cos 5. Router connected is 891 with IOS 12.x. Traffic is untagged and being sent at a rate of 2...
Thanks for help in advance. I have a fiber 10mb connection delivered as Ethernet. I have a 2811, (1) HWIC -1FE and (1) HWIC -4ESW. I would like to know which module I should use and configuration example. Also, my ISP gave me serials and my LAN block...
