hello eveybody we have 2 switches where they have same configuration with snmp and access list but still yet they are not working one does work fine and sends alert while the other doesn't send any alert i tried pinging zabbix there is ping without a...
Forum Posts
Hello, We need to configure ERSPAN on cisco 3850 and 3650 Switches The source ERSPAN will be C3850: with the below configurationmonitor session 11 type erspan-sourcesource vlan 2140 - 2141destinationerspan-id 100mtu 1500ip address 10.137.200.1 "C3...
Switch: Cisco C9200L-48P-4XIOS XE Version: 17.12.03 (cat9k_lite_iosxe)IP Phones: ShoreTel 115 and Yealink T30PAccess Points: UniFi AC ProAll switch ports are functioning for data transmission, but none are supplying power to PoE devices. I have alrea...
Resolved! 9410 and 9407 recommended mature release
Hi, I'm about to update two 9400 switches, one 9410, one 9407. Going through the 9410R downloads section recommends 17.9.5 as the latest mature release. However, the supervisor module download page suggests 17.12.4.
I've been trying to work create a network with multilayer 3650, that has STP and DHCP, and got stuck on the STP part.here are the commands I put in my topology, in the order I put them -MU -int ra g1/0/3-5switchport mode trunkswitchport trunk allowed...
Resolved! Cisco Nexus Switch 6001
We have a Cisco switch (Cisco Nexus Switch 6001) where we need to configure a VLAN IP like a normal switch(Normal Switch #Interface vlan1#ip address 192.168.0.1 255.255.255.0, but there is no option available. How can we configure the VLAN IP on this...
Hi,Can someone help me in a problem related to HSRPMy standby router is not able to ping virtual ip, active router is pinging the same.My HSRP is working i.e shifting to other router.Noticeable thing 1. when i provide manual mac address then hsrp wor...
Resolved! Cisco packet tracer help
I am new to PT and taking the online intro course.In the sector Video - Deploying Devices Example they connected home router to a webcam. I tried connecting mine on my PT but it keep getting connection error: The cable cannot be connected to this por...
Resolved! 9300 Cleanup Fail
Hello, all.On a couple of stacks, when I run "install remove inactive" I get the following message:install_remove: START Thu Sep 12 12:02:24 EST 2024FAILED: install_remove : The input file INVALID is not a valid fileIt is version 16.5.1a.Here is the ...
Does C9500-48Y4C-A support both SFP and SFP+ RJ45 module? Have checked the https://tmgmatrix.cisco.com/?npid=50 Cisco Optics-to-Optics Interoperability Matrix for combability, it is on the list. But from Cisco commerce online configuration, there is ...
we need to carry out simulations in the laboratory and consequently allocate memory or CPU at 90% as the DNA Center has been unable on several occasions to detect this condition in the Catalyst 9200 and 9300 series switches while other SNMP monitorin...
I don't understand differences between Catalyst 9300, 9300X, 9300L, 9300LM. And also I don't understand the meaning of those extension. Someone please help me to understand those.C9300X-48HX -> HXC9300X-48TX -> TXC9300X-48HXN -> HXC9300X-12Y -> YC930...
I'm working with a Catalyst C9500-32C on version 17.1.1. I have a QSFP-4SFP25G-CU5M module in port 2(the port is breakout enabled). Cisco Optics-to-Device Compatibility Matrix shows that QSFP-4SFP25G-CU5M is compatible with C9500-32C on version 17.1....
Hi Guys,I have a head scratcher that I'm dealing with. I have 2x (2 month) 6880-x switches configured with vss with 2 vsl links on each of its sup cards and switch 1 is the active switch on the vss. Both 6880x chassis also have 2 additional 10g mod...
Resolved! % Authorization failed.
Hi Team, Whenever i am executing any command in a router or switch, i am receiving following error, if try for more than 2 to 3 times, the command stats executing. please advise what is the cause for this error and how to rectify this? CE ROUTER#sh...
