Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Hi i m going to convert my two 6500 to VSS , i have the below module on each 6500 . does the VSS work fine and well with modules listed below?? , pls give me video for VSS implenatation and verifactions1 48 48-port 10/100/1000 RJ45 EtherModule ...
Dear Friends.I need to use cisco 3750E switch on core. I want to know whether BGP is supported on this model or not?Currently i have c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin" preinstalled. and i checked BGP is not supported o...
Hican i have 4 links from an ESX server to 6500 , each link represents a trunk link carries each the same 2 VLAN , 100 and 101 , keep port-channel out of the picture , does it work well???thanksIbrahim
Hi ,We are planning for fiber cabling/connectivity between our two office locations. Please see the below attached diagram.As of now the distribution switch (3750) is connected to access layer switch (2960) via SFP 1000BASE-SX port. According to the ...
I'm trying to figure out how to (or if I can) setup the management interfaces (fa1) on a couple of new 4500X switches. My issue is that the 4500X's themselves are the gateway for my management VLAN (.1 HSRP virtual, .2 and .3 SVIs on the pair of swit...
We just purchased a Nexus 7010 switch and we are at a stand still with our COLO trying to figure out what power source should be provided. APC recommends a 50amp 3phase vertical cabinet PDU (AP7867). What type of power source\breakers will be suffi...
Need to Have both ISP to access internet/serversI need help to configure a Cisco 2911 router, It has two ISP one as primary 216.140.140.0, and secondary for backup as 216.150.150.0.I need to be able to access both the ISP's using the same interface...
Hello everyone,Please see the attached ppt. The question is: is it possible to have both PCs on the same LAN accross the network with Foundry and Cisco switches?Thanks,MD
Hi,Attached setup i am planning for testing multicast output from different vendors using VLC and STB. This Setup made to test the picture quality between the vendors at the same time on the multiviewer screen.1) Only a 2960 Gig port switch with on...
Hi.i want to kn ow that where is a image of firewall module locate? at firewall module flash or supervisor? how i upgrade the imageof firewall module?thanks
Hi,I have attached a quick image for the network in discussion here.Current Situation:- All servers are connected to the Core 6500 switch. Layer3 VLANS also exists on the same switch. Users reach the Core and access the servers. No firewall in place...
Hii have server with two uplink to pair of 6500 non-VSS, this server member of vlan 100 sw-1 is active HSRP while sw2 is a standby HSRP , how can i make this server forward traffic on both Link . the server admin told me only one link is active (gree...
Could somebody tell me how to check whether other path available if OSPF route in the routing table fail?
I have a c3560e-universalk9-mz.122-55.SE5.I have 3 distinctive Vlan's:Vlan 100: 10.8.33.0/24Vlan 200: 10.8.133.0/24Vlan 300: 10.8.233.0/24Inter vlan routing is working.My default gateway is 10.8.33.254.I need to send some traffic in vlan 100 the rest...
Hi,I have a 6500 with 2 SUP7203B in Hot-Standby and when i reload slot 5 it goes in rommon (slot 6 is still up and takes over fine).When it is in rommon and I simply type boot, it loads the image fine.Why it doesnt boot by itself directly??I use SXI3...
