Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Resolved! redundancy setup

Hi,I need some clarifications to design the network with below requirements .Current Situation============We are able to reach server IP -10.203.206.40  from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.   Req...

Shibu1978 by Level 1
  • 1428 Views
  • 14 replies
  • 0 Helpful votes

I've been researching the 3750-x Netflow support but I'm not 100% sure of how much support it has. From what I've read the only way to get NetFlowsupport is to install a specific module that provides NetFlow. I also heard about how it might support s...

Resolved! mirror a port

Hello,At moment I have mirrored a single port and am pointing the data back to the netflow server:monitor session 2 source interface Gi1/0/28 (data I want to capture)monitor session 2 destination interface Gi1/0/17 (mirrored port)Is it possible thoug...

ohareka70 by Level 3
  • 942 Views
  • 3 replies
  • 0 Helpful votes

Hi,Is there a way to set the columns' width of the sh int sum output? It's too narrow for the 10GbE interfaces:switch#sh int sum | i ^\* Te|^\* Gi* TenGigabitEthernet    0     4    0     0 467347000  60834 164015000  23424  911* TenGigabitEthernet   ...

I haven't done a ton of routing (mostly switching and firewalls) so I'm looking for a little advice.  I've inherited an existing network and am looking at making some routing changes.  There are several branch office routers all connected in the same...

Router: 3600 SeriesFlash: c3640-i-mz.122-29b.bin6 Channelized T1/PRI portsOne of our T1 crashed do to rain storms. It's a wet pair that causes the drop. Which is not my concern at the moment.What i am facing with is that the Router has to be rebooted...

Hi,We are looking to deploy either appletv or airserver to support the demand for mirroring ipads/android/laptops to projectors in our classrooms. I'd like to leverage the existing hardwires computer/vpu and install airserver and allow the pc (ethern...

Hello,I have this error message on my many catalysts on our network:%C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 43199 times)Packet received with invalid source MAC address (01:80:C2:00:00:01) on port Gi1/1 in vlan 501I looked on my network, ...

Resolved! BGP to OSPF

Hi Could anyone help me?My simplified scenario is:I have two iBGP neighbor neighbor X.X.X.Xand neighbor Y.Y.Y.YI am redistributing BGP into OSPFand I need neighbor X.X.X.X to have lower metric than Y.Y.Y.Y in OSPF domainhow can I solve this?thank you...

baxta2712 by Level 1
  • 1199 Views
  • 4 replies
  • 0 Helpful votes

Hi,We have a Cisco 2801 running “c2801-ipvoice_ivs-mz.151-3.T2.bin”We are trying to register to the Skype service using a Cisco CUBE, however so far no luck.One question I do have is with regards to how NAT plays a part in this process? Do ports need...

dwaters by Level 1
  • 6074 Views
  • 6 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card