Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

HiI need configure qos into the LAN classifying traffic by using  ACL, i have the follow configuration on my SW 3750E (example);the result is that the brand not as classified, any ideas ??mls qosmls qos map cos-dscp 0 8 16 26 32 46 48 56access-list 1...

Hi AllI have trawled through the Cisco website and am struggle to find the answers to the below question, is any able to helpDo the Cisco 2960 and 2960S      series switches support 802.1X-2004? Cisco 2960, is there a planned end of sale for these s...

          Hi         On a Cisco 3560 with IP services ver. 12.2(35)SE5 I have tried to config BGP with a 6-digit AS number, and it is not possible. Is there someone who knows what software is needed for 6 digit AS number for PI IP addresses, and do I...

ejrgensen by Level 1
  • 5227 Views
  • 5 replies
  • 0 Helpful votes

Hi all, This question may be bit OT to this forum but i need some suggestions on it. We are planning to deploy SSL based solution that will provide customers access to our portal. We are planning to use 2 different ISPs for redundancy purpose, so i a...

Jonn cos by Level 4
  • 4855 Views
  • 6 replies
  • 0 Helpful votes

On our edge router the CPU utilisation was quite high. On checking further we could see that the broadcast on the LAN interface was quite high. - Not sure if this can cause high CPU usage?Interestingly the broadcast count in sh ip traffic result does...

Hia simple question, please advice me if I have 500 equipment, and I want a monitoring server use ether snmp/cdp to monitoring systems,which one will be better, and cause less perfermence issue, and less traffic issue.Any comments will be appreciated...

julxu by Level 1
  • 1287 Views
  • 3 replies
  • 0 Helpful votes

Hi everybody.I am trying to learn SMNP. My lab scenario is:R1---ethernet-----NMS ( Orion by Solar wind)What is minimum configuration required for SNMP?According to link, shown below. this is minimum requirement:http://www.techrepublic.com/blog/networ...

sarahr202 by Level 5
  • 4613 Views
  • 3 replies
  • 0 Helpful votes

I am finding trouble getting static neighbor commands for EIGRP to work when I am studying in GNS3.My understanding is that all I need to do is type neighbor 192.168.1.1 ser0/0 in router configuration mode and as long as:1) Serial0/0 is part of the 1...

hi , from ccnp route cisco press book , the last of ipv6 tunneling i have a table Table 18-4      Comparing IPv6 Multipoint Tunnels                                Topic                                                             Automatic 6to4      ...

Dr.X by Level 2
  • 390 Views
  • 1 replies
  • 0 Helpful votes

Hi I'm trying to configure "IP PIM SPARSE-MODE" command on a vlan interface on a 3560E switch but it doesn't give me the option to do this. The only option available is ip pim passive. What would cause this ? On the same switch a physical interface i...

harryraju by Level 1
  • 2730 Views
  • 2 replies
  • 0 Helpful votes

HiI just got my Cisco SG300 28, but I have some problems getting the routing to work. I get the vlans to get to the router, with the default route. But not getting them to talk with each other. I can ping the IPs from the cisco, but I am not getting ...

I have a customer with a 3750x4 stack. We rebooted the stack over the weekend and the master did not come back up. Upon investigation it was discovered that tghe master was set for Manual Boot. I tried issuing the "no boot manual" command in Global C...

Review Cisco Networking for a $25 gift card