i have 2 routersr1-fa 0/0-ip address -192.168.1.1r2fa 0/1-ip address------192.168.2.1 i have connected them by fast ethernet .can i ping them?if yes then---Posted by WebUser Brijesh Akbari
i have 2 routersr1-fa 0/0-ip address -192.168.1.1r2fa 0/1-ip address------192.168.2.1 i have connected them by fast ethernet .can i ping them?if yes then---Posted by WebUser Brijesh Akbari
Hello experts,i am to design( and i eaisn only design) a soltuion for fully redundant network (or server links). I have come up with this design:i have assumed that all ther servers have NIC teaming enabled( for redudnancy ofcourse,, one link is acti...
Hi I have a Home lab setup. I am planning to implement VLANs for my homelab. I am looking for base model cisco switch which can provide 1 GBps of speed and should have capability to configure VLAN's.
Hy,Here's bootup log:Cisco 2821 (revision 49.46) with 118784K/12288K bytes of memory.Processor board ID FCZ101372P94 FastEthernet interfaces2 Gigabit Ethernet interfaces2 Virtual Private Network (VPN) ModulesDRAM configuration is 64 bits wide with pa...
Hello,I am using GNS3 For a topology as in attachment. I configure EIGRP on all routers. R! and R2 has 2 link with same bandwidth (1544). R1 routing table show both path due to same metric. But when i change bandwidth (3544) on s0/1 on R1, metric of ...
Hi There,We are experiencing continuing high CPU issues on our 6500 (generally 80+% most times).#show proc cpu sorted | exc 0.00CPU utilization for five seconds: 75%/67%; one minute: 69%; five minutes: 68% PID Runtime(ms) Invoked uSecs 5Sec ...
I use IOS Software, ME360x Software (ME360x-UNIVERSALK9-M), Version 12.2(52)EY2. I not found the command "ipv6" on global and interface configuration.
We have an old Cisco 6509 with 2 x Sup-720w/MSFC3 running 12.2(18)SXD6. IOS version is pretty old, and Cisco's software download section doesn't even have it in the list anymore.We would like to upgrade IOS to the newest/latest, but we're not sure w...
Hi Can anyn one help how to solve this problem.This switch has been stucked. Traceback= 482608 4C00E8 758DA8 752FEC%SYS-3-CPUHOG: Task is running for (1895265)msecs, more than (2000)msecs (90/1),process = Hulc Storm Control.-Traceback= 482610 4C00E8 ...
Ok So ive got multiple VLANS on a L3 switch and I basically want to use a VLAN Access List in order to block communication between each of the VLANS, except one which will provide internet connectivity (there may be a better way to do it?).Basically ...
I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the o...
Hi everybody,I wan to know if it's possible in Cisco switch 2960S that support 1G per ports to limit the speed to 100 and duplex to Full at max but using the auto negotiation process for the end device.thx
Folks, I have a 3560 and when I try the "mls qos trust cos" command under the port channel interface it does not work. Any ideas?The command does work under the indiviual interfaces but not under the port channel interface.cat3560(config)#in...
Hi I am using Jermey's new CBT nuggets for CCNA and was making topology on gns3 all is going well but when I tried to make vlan interfaces its give me this error.interface vlan 64ip address 10.1.64.1 255.255.254.0description "Voice Vlan"interface vla...
Hi everyone, can anyone tell me if I can run the Cisco AIR-LAP1142n-a-k9 access point in standalone mode? I don't want it to look for a controller when it boots up.Please advise.Thanks
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-19-2024 05:58 AM | ||
04-19-2024 02:04 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
12 | |
10 | |
8 | |
7 | |
7 |