Switching

I need some config help with the following. I realized at the last moment during an office relocation that the ISP is not providing a router to terminate the public block.  I have a Cat3560 which can handle static routes. ISP info:Routed block 24.25....

   Hi,i need support about the steps for installation of license ipbase from evaluation ipbase on 2 different stacks of 3750-X. the 2 stacks are composed of 2 3750-X with ipbase evaluation and i want to install the ipbase license bought and remove th...

hi, i am configuring a server with two intel NICS. i have coneccted each interface trough two different switches, and the intel teaming set to Switch Fault Tolerance (SFT). I have STP in the L2 network, and set BPDUGUARD and PORTFAST in the teamings ...

Hi,We are going to use CUE and CME on cisco 2900 series router.We would be using 24 port L2 POE switch as well.Our Ip phone going to be have switch port so that cable from POE goes to Phone and from from Phone to desktop.Means vlan should sense the d...

Hello All,I'm facing to a very strange problem.I'm trying to wake-up stations from a server into a different VLAN, but through OSPF routing and multiple L3 Switches hop.Look @ the joined topology scheme. (!! BE CAREFULL !!   This is a NO PASSIVE INT...

Hello,I'm seeing an increase of Throttles and/or rx_soft_overflow_err on a Fastethernet interface.I did some research and can see alot of references of this being caused by input errors.Yet I'm not seeing any other counter increase on this interface ...

Hi Expert,I found error %ETHCNTR-3-LOOP_BACK_DETECTED: Loop-back detected on GigabitEthernet Now, i disable keepalive and error disappear but i need to know this error cause network loop or software bug?IOS:12.2(53)SE2Thanks for all reply

There are two Catalyst 6509-E switches with two Supervisor 720 modules on each of them. I need both supervisor uplinks to become VSL links, so i have configured Ten5/4 - 5 and Ten6/4 - 5 (these ports are on Supervisor modules) as VSL links, where:   ...

Hi, How can I prevent my network form virused PCs. Las night i had problems on my network and aftech checking logs in my 3560x there was problem with MAC flap.Is possible prevent network from this with config in our switches?ThanxBRDave

Hello everyone.I have a 2x Nexus 7018 set up as a distribution switches connected to each other connecting to about 47 Cat 4507 edge switches.  All but 4 of these switches are working properly.  The nexus is running code 5.0 (2a) and the 4507's are r...

Hello, everyone:I am encount a problem when I do a Local SPAN on an 3750 Switch.My 3750 runs on  version 12.2(25)SEB4 IOS .I need to SPAN two port's traffic to one port to work with Websense.  The port  needs to be able to monitor and send traffic.  ...

I have 3 3750's (not stacked, they are at different floors) with a total of 60 user vlans all together, we are trying to allow each vlan to the internet and block access to any other vlan.so sayvlan2 : 192.168.2.0\24vlan3 : 192.168.3.0\24......vlan61...

Hi to all,I would like to seek your help regarding my problem. I have a client that have a combination of cisco & hp switches. They want to implement redundancy & aggregation. I suggest using LACP for aggregation (cause it is used by HP) & STP for re...

Hi All,I am in the process of developing a spec that is to be used for the purchase of a significant amount of Cisco switch hardware, mainly from the 2000 and 3000 series.I was wondering if you could help me confirm that I have included everything.20...