Hi all, I wanna configure ip dhcp binding client ip to mac address using web gui. We're using 9300 and DHCP server is here also.I know how to achieve that using the command line but somehow our client asking to teach them using web gui. Is that possi...
Hi Team, I want to know if Cisco Cat C9200L-48P-4G and C9300 Switches supports TACACS+ (ACS Version 5.8.0.32). Thanks and Regards.
Hello,I'm a student and I'm currently trying to understand EtherChannel and Vlans. You'll find a screenshot below to understand what I'm trying to do.I want to make 2 Vlans, MGMT and Guests so they can't ping each other. I also have 2 Multilayer Swit...
Hello all!I am in trouble:My switch is WS-C2960X-48LPD-LBThe IOS is c2960x-universalk9-mz.152-2.E7.binI receive error messages:Dec 28 09:17:52: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PDDec 28 09:17:52: %ILPOWER-5-POWER_GR...
Good Evening,I have a 2 Switch Stacking <A> and <B>, I need to know1- is the logFile of the Switches be in the main Switch (Commander) ? or every switch have the log file separate from Active SW? 2- if I use SNMP to Send Trap, how can identify every ...
Good morning, I have to create a lot of NAT's in order to navigate some machines. The issue is that can't to create a Overload assigning the IP from interface because I wan to exit with different IP. Then I am trying to create a pool with unique publ...
We have a switch stack that is showing two of its three power supplies as bad, and reporting no input power. However from the hardware perspective, all of the LEDs on the device itself are green. I have been unable to find any documentation online ...
Why on earth did Cisco not support the SFP+LRM module with their QSA CVR module? It was not until we installed our C9500-32QCs and C9606Rs did we realize we had major problems. It slipped by us -- I did a lot of testing and must have missed that poin...
Hello Community, I use three SG300 switches to run my network. One is connected to a (free) ESX server running an OPNsense VM that acts as router. I have several VLANs that are connected using trunks between the switches and ESX. The OPNsense VM is c...
I have a WS-C3650-48TS running on IOS ver 16.6.7. I have seen log entries like following for the interfaces where no device is connected.I have seen similar logs entries for interface Gi1/013 & Gi1/0/14. There are no other log entries other than the...
Hi Everyone, Currently I am installing Cisco C1-C4507R+E for our costumer.They purchase Image with code "S45EU-S8-310E" and description "CAT4500E SUP8E Universal Image". It is shipped with IOS-XE with CAT4500E SUP9E/ 8E/8L-E Universal Image (cat4500...
We currently have 2 brand new switches in a stack. The master switch works great, but the standby switch is slow and particular devices like IP phones connected to it are nearly unusable. The phones lose connection to the server and freeze up. If the...
Hi How can I determine the IP address of my Cisco SG200 switch?I don't know what the IP address and network are.I can't seem to reset my switch because the reset button is broken off. Any ideas? Thanks in advance,
Hi We need to add layer 3 switch (MS-250 Meraki) to perform intervlanwe have SAS 5506 That connect to vpn (Anyconnect) in vlan 1 ip 192.168.1.1all connection go from this vlan 1 to the server,workstation,printer,vpn......we need to divide our networ...
After firmware ugrade c2960x-universalk9-tar.152-7.E3.tar done in gui my switch will not boot.my only iI have connected it to usb /terminal and get this output :
| User | Count |
|---|---|
| 14 | |
| 11 | |
| 10 | |
| 7 | |
| 7 |
.jpg "VIP Community Legend"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
