Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hey everyone,We've just purchased anew 2821, however the software is out of date and I don't have a CCO login. So my question is, what smartnet contract will give me access to downloads (vpn client software, SDM updates, etc), without breaking the ba...

Hello AllIf I have two 6509's running as our core network and each 6509 is the active switch for half of the vlans. The 6509's are connect via 4 ten gig L2 port channel. My question is, when configuring HSRP is it necessary to enable port tracking in...

dvanzee by Level 2
  • 1451 Views
  • 6 replies
  • 0 Helpful votes

Hi,Looking for some advice on creating a SPAN port. The situation is something like this: there is an existing replication server (say ABC) and there is another server (say XYZ) which is sort of acting as log collector server. SPAN needs to be create...

suthomas1 by Level 6
  • 572 Views
  • 3 replies
  • 0 Helpful votes

Hi All,I am after a bit of advice. I currently have a 1Gbps connection between two sites. The server guys are looking to locate a backup of the companies TSM Backup solution at each of the sites - this will involve a lot of replication traffic betwee...

Hi, im new to Cisco (almost done with the first book), and i recieved a switch from my workplace. I get the thing set up with the serial to console port and the like and notice that I don't get the initial config dialogue, so I erase the startup-conf...

Roberek99 by Level 1
  • 1970 Views
  • 4 replies
  • 0 Helpful votes

Hi All    I am configuring a Wireless Bridge which seems a little more difficult then it should be on the Cisco stuff. I ended up going through a config guide from Cisco and got it up and running.  The only disturbing thing is that the guide only spe...

blittrell by Level 1
  • 1077 Views
  • 3 replies
  • 0 Helpful votes

We have a new Nexus 7k, in the data centers we are noticing the switch ports for firewalls being flooded with ICMP requests at a very high rate..Is this normal, is there something we are missing ?? Thanks In Advance..

I think I have this figured out, but I'd like to see if somebody could double check me.I've got 2 access switches connected to each of my 2 distribution switches via etherchannels. On my distro switches(L3) I should configure bridge groups for each v...

Hi All,Im wondering if someone is able to help with this one. Please view the debug output below*Mar  1 05:01:07.270: IP: tableid=0, s=119.118.126.234 (local), d=119.118.126.233 (Vlan1), routed via RIB*Mar  1 05:01:07.270: IP: s=119.118.126.234 (loca...

I am trying to upgrade a 4506 w/ Sup V from cat4000-i9k91s-mz.122-20.EWA2.bin  to cat4500-entservicesk9-mz.122-50.SG6.binI currently have 512 MB of Ram and 56.50 MB of bootflash my current PROM is ROM: 12.1(20r)EW1                                    ...

Mike Mott by Level 1
  • 849 Views
  • 5 replies
  • 0 Helpful votes

I have a customer whose routers and WAN we provide and maintain.  There are twenty 2821 routers each with a 4-port HWIC-ESW module in them.   We provide the customer with Metro Ethernet for Data and VoIP between their sites.   The 2821 routers connec...

Hi guys,  I am running a lab through dynamips using isis. I have a router R5(L1 router) which is connected to R6(lL1-L2 router). R6 is connected with  other L1-L2 routers. I tried to change the ATT-bit when R6 sends LSP-L1 tou R5 when the backbone ar...

Review Cisco Networking for a $25 gift card