Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

I have an environment where I install a bunch of servers before I ship them out to a customer.  At the customer site I have a DNS server of 10.10.10.10. And a subnet of 10.10.10.0/24In my environment here, I have a corporate DNS server at 172.16.0.10...

jfraasch by Level 3
  • 1316 Views
  • 1 replies
  • 0 Helpful votes

Resolved! OSPF Help

Hi All ,                 I have 2 no of 4506 Switch holding 6 L3 Vlan connecting downlink to 6 no user access segment switches ,and uplink connecting to 2 firewall , I am running HSRP among each VLAN for gateway Redudancy , 3 Vlan will have higher pr...

Hi guys I would like to configure my routers to provide public IP addresses to  clients. eg blocks of addresses eg 6 routable staticpublic IP add for client 1, 30 for the next client. etc I know I have to do point to point (/30) links between clients...

cm by Level 1
  • 452 Views
  • 2 replies
  • 0 Helpful votes

HiI'm trying to xmodem an image on to a recently purchased, secondhand 6509 sup2 MSFC2 which is completely offnet with no image on there at all.The problem is that whenever I try using xmodem to transfer the image over from my laptop it fails, for an...

Hi @ all,regarding the rps 2300 there´s something i didn´t figured out. We have a RPS 2300 with one 1150WAC power supply. On this RPS theres only one 2960 connected.    RPS2300----RPS 2300 power cable connection--->2960<--------inline power-------|No...

I have a 3750 switch that has a bunch of workstations plugged into it, I'm having an issue where alot of the ports have a good amount of output drops and I can't seem to figure out why.  All the workstations are on 1Gb links and are very underutilize...

niro by Level 1
  • 5933 Views
  • 1 replies
  • 0 Helpful votes

I have an extended ACL applied inbound to my two external interfaces (two separate ISP's using BGP). Within the ACL, I have an ACE for allowing established TCP connections, i.e. "access-list 100 permit tcp any any established ".Will this cause a prob...

kduckett by Level 1
  • 3723 Views
  • 13 replies
  • 0 Helpful votes

I have two new Cisco 2960G switches, and I must be doing something wrong because the only time I can successfully consolethese switches is if I have the session open during the switch startup.  If I have the switch on already and try to connect, noth...

We have a Cisco 3750 that has a span port setup, to mirror traffic from all the other ports.  Right now we have our IDS connected to that span port.  But we now have a need to have a second device see that same traffic.  In the old 10/100 days we cou...

We need some new patch panels at my company. I am thinking about going with blank keystone patch panels (ex. http://www.amazon.com/StarTech-BLANKPATCH24-24port-Blank-Keystone/dp/B00066HS44/ref=sr_1_2?ie=UTF8&s=electronics&qid=1263479274&sr=1-2). The ...

Let me explain the topology a little.We have these 2 networks that consist of seperate medical device networks that communicate with each other via there own VLAN'd network.  (SIP phones and some Nursecall servers and switch)   each VLAN houses these...

bradsantee by Level 1
  • 2295 Views
  • 13 replies
  • 0 Helpful votes

HiLately we are getting a lot of excessive errors on ports where a AP is connectedsh int fa1/0/25 | i error|runt     669 runts, 0 giants, 0 throttles     669 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored     0 output errors, 0 collisions, 0 inte...

BartV1982 by Level 1
  • 1009 Views
  • 0 replies
  • 0 Helpful votes

I am having a duplex mismatch on faste trunk uplink between a 2950 and 6500. The 2950 auto neg at full/100, the 6500 auto neg at half/100. I tried adding the command "duplex full" on the 6500 interface and drop connection. This is my interface config...

kris55s by Level 1
  • 1097 Views
  • 5 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card