Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Does anyone know the port distribution to different ASICs in 3560E ? I can see three ASICs in the show command ? Switch#sh platform port-asic versionPort-Asic Version Info:========================ASIC-0: Version:3 DeviceType:0x2ABASIC-1: Version:3 De...

s.uslay by Beginner
  • 880 Views
  • 2 replies
  • 0 Helpful votes

Hi everyone,I created a manual binding for my DHCP service but it never worked. It always receives the dynamic PI from its parent pool. ip dhcp pool parentPool network 10.1.1.0 255.255.255.0 default-router 10.1.1.254 dns-server 139.130.4.4 61....

Hey,I will be removing our FWSM from our 6506E and I have a question. Is there anything I should know about removing them... other than pushing the shutdown button and waiting a bit?

Ok, this is my first private VLAN and maybe I am not getting the concept here but my isolated port cannot ping the IP address of the Primary VLAN interface.How do you route Isolated ports? Do I have to configure a port as a L2 promiscuous and attach ...

Brian M by Beginner
  • 449 Views
  • 4 replies
  • 0 Helpful votes

Hello,Can you please help me find some installation and configuration example using Catalyst 4507 series switch, what are some of the features available of this switch.Thanks for your support.-chie

lazon by Beginner
  • 237 Views
  • 2 replies
  • 0 Helpful votes

Hello guys,I would like to know if there is a function for us to disable errdisable state detection in IOS.Normally any interfaces will go to errdisable state because of many possible causes such as duplex mismatch.I am hoping to avoid the interface ...

Hi,based on your experience,which TFTP server works best,i have used 3cs & 3CDAEMON and it download/upload to a particular size then times out,kindly guide me to a TFTP server that can do 54MB and above-i really appreaciate,i have to upgrade a router...

I have a situation where I have wireless phones and Access access points that need to get DHCP and that reside on the same VLAN. I also have laptop devices that were improperly configured for the same SSID/VLAN. I would like to implement something ...

p-blake by Beginner
  • 348 Views
  • 5 replies
  • 0 Helpful votes

Hi every body!i have few question about roaming in wireless lan. All access points are autonomous in my example.case#1roaming within subnet:two ap(ap1 and ap2) with overlapping each other cell but differerent sids.ap1 has ssid abc,while ap2 has ssid ...

sarahr202 by Contributor
  • 409 Views
  • 1 replies
  • 0 Helpful votes

is it possible to policy route based on protocols? i would like to run policy-map on a Cisco 3550 and it route port 80 (wwww traffic only) out a seperate device and have all other traffic go out its default route. thanks for any info or links!

j.cambray by Beginner
  • 348 Views
  • 1 replies
  • 0 Helpful votes

Hi, There is a packet loss between systems of same vlan connected to same access switch."Pinging from 172.16.5.186Pinging 172.16.5.78 with 32 bytes of data:Reply from 172.16.5.78: bytes=32 time<1ms TTL=128Request timed out.Request timed out.Request t...

BELOW IS MY CONFIG. HOPE SOMEBODY OUT THERE WOULD HELP GET THE RIGHT SOLUTION. THANKS.1750#show versionCisco Internetwork Operating System Software IOS (tm) C1700 Software (C1700-Y-M), Version 12.1(3), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2000 by...

napoleon8 by Beginner
  • 574 Views
  • 7 replies
  • 0 Helpful votes

We have a router with only two interfaces. Could you use it to make another subnet on our LAN when it will not be the gateway address on everyone's PC? The Gateway address is a modem to the internet. I can see setting the router as a gateway address...