Switching

C3750 switch fails post with the following-Waiting for Stack Master Election (around 30 seconds)...POST: PortASIC CAM Subsystem Tests : BeginTCAM (asic:4) walking-one test failed Write: 80_00000000_01000000-00_00000000_00000000 Read: 80_0000000...

I know OER map support prefix-list and access-list, but we when do a test in IOS 12.2-12.4T, it's only support prefix-list and can't input access-list. Is there anybody configure OER map with access-list scuuessful, please help me. Please tell us the...

I am trying to implement PIM snooping on 6509 running 12.2-18-SXF11But it is not working.My topo:sender | |router(RP) | |6509--firewall2(standby) | | | | ha | | | | firewall1---switch1----recieverI am have enabled ...

Hi all,My setup is :SW3 Cisco 6509 Switch -> Vlan Trunk (through LAN Extention) -> SW1 Cisco 6513 -> Etherchannel Vlan Trunk -> SW2 Cisco 6513 -> firewall (fortigate) -> internet...The PC can ping from SW3 across to the internet without any issues.Al...

I have a setup shown in the diagram. The speed and duplex are hard coded on both the server and the Cisco 7140 and the switchport on the blade.Servers are hard coded to 1000-full and Cisco 7140 is hard code to 100-full.Same thing on the Catalyst 650...

Say i have this 3750 switch inside my company. Somehow, the connection to the switch is slow. The only way to access to the switch is using console.Inside the console mode, I could not type in any words because the log messages appear faster than my ...

hi, I test this config on a lab for exam bsciwe can see it here:http://safari.oreilly.com/9781587201936/ch25lev1sec4I'm asking what will be the route on the left network to join the right and vice versathanks

Hi all, I'm running EIGRP key-chains and authentication from one router to another and after configuring one side i get the expected routes start to flap. But also i can still ping from one end of the link to the other. Why is that if the authenticat...

Hi NetPro,does anyone who encountered this problem before ? show proc cpu hit to 96% .what is the most common problem caused this ? CPU utilization for five seconds: 82.56% one minute: 69.16% five minutes: 6...

Hi all, Can anyone tell me what a directed broadcast is, and what/who would use one? on my layer 3 switch are these enabled by default ?

Hello,In the same OSPF process, within the same area 0, i want to filter subnet advertised by a router.Exemple:Router A,B and C are in Area 0. They all have a i address in the subnet 10.1.1.0But router A advertise routes from other enterprise. Then o...

Hi,The following excerpt is taken from Cisco documentation: The WS-X6548-GE-TX, WS-X6548V-GE-TX, WS-X6148-GE-TX, and WS-X6148V-GE-TX modules have a limitation with EtherChannel. For EtherChannel, the data from all links in a bundle goes to the port A...

HiCurrently I have the following configured on my router, what I'd like to do is put this on my 3750 switch, my question is what changes do I need to make to enable this to occur:interface FastEthernet0/0 ip address 10.11.8.2 255.255.248.0 no ip redi...

Hi all, when using cos for my voice phones, if i have a pc and phone plugged into the same port, the phone is vlan 2, the pc is vlan 1, how does my switch know to put the phone in vlan 2, does it see that the phone has a 802.1p tag, thus meaning its ...