Resolved! rate-limit BPDU
hi all,is there a posibility on 2960 or 3560 to limit number od BPDUs? for example to 100/s. Because when network loop occur the switch is bombarded with BPDUs and the swich has to process all of them by CPU.thanks a lot
hi all,is there a posibility on 2960 or 3560 to limit number od BPDUs? for example to 100/s. Because when network loop occur the switch is bombarded with BPDUs and the swich has to process all of them by CPU.thanks a lot
Dear expertPlease provide me any hints or useful web links, thanks you.
HII Want ur Help:I have 2 oulets in my Room connected to 3550 Switch(vlan 9) but the Problem is i want to add another 5 computers but no enough Outlet waht am thinking is to Add a d-Link Switch 8 ports to the outlets(connected to access-port on vlan ...
Dear NetProwhich commands are Powerfull to limit JOIN On certain routersviaip igmp profile 1permitRange 228.28.28.0 228.28.28.254int X ip igmp filter 1orVia a Normal access-list10xs
Hi,I have read through the BCMSN Study Guide and Cisco.com product guide on ISR 3825 and that it supports SPAN on both routed and switchports.I have a NM-16ESW on the 3825 but I hit a brick wall when I tried to SPAN a routed port with error message:I...
Hello,I noticed the following behaviour on several switches running ios (e.g. WS-C4507R Version 12.2(20)EWA):After configuring snmpv3 likesnmp-server user <v3-Username> <group> v3 auth md5 <authkey> priv des56 <privkey>snmp-server group <group> v3 p...
Hi,Can I use auto mdix on WS-X6748-GE-TX card with native IOS ?I read some information that with Catos the command is supported but nothing about IOS.Regards
Hi all, I have a CE500 Switch(WS-CE500-24PC), as I forgotten the password of the switch I need it to be reset to the factory default. As it doesnt have any console port, I was following the link below to reset the password. http://www.cisco.com/en/US...
HiCould some one help me with the following. Basically I'm looking to make an update on the metric for an OSPF process on router. I assumes I will need to clear the routing table after making the change, but will I need to clear the routing process o...
If you've got a network consisting of all Cisco equipment and you've maybe only got a couple of VLANS should you run RSTP rather than the default PVST? And if you've got a lot of VLANS should you run MST? I've been doing quite a bit of reading in t...
Hi all, I need to sell LWAPP to my manager, we currently use the CWLSE to my knowledge, but I dont know what benifits this is giving us as it seems just a radius server for WDS at the moment. I would like to use LWAPP in future for all wireless insta...
Hello everybody; I have enabled CEF with per-destination load balancing on 6506 MSFC2 with PFC2.I see an unexpected behaviour. There are 5000 entries in the routing table and 4 available next-hops. I see an unequal distribution of traffic between t...
can your access-list limit user from accessing the web? what symptoms would be encountered.
Hi, On our cisco 4507 switch whenever a interface goes down the logs are not generated? Following commands are configured for logging :logging buffered 16000 informationallogging console informationallogging monitor informationallogging facility loca...
Hello, To check the status of spanning-tree on the ports of my switches (on vlan1), I do an snmpwalk on object dot1dStpPortState (1.3.6.1.2.1.17.2.15.1.3) of BRIDGE-MIBsnmpwalk -v 2c -c public myhost 1.3.6.1.2.1.17.2.15.1.3SNMPv2-SMI::mib-2.17.2.15.1...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-06-2025 04:11 AM | ||
02-02-2025 10:25 PM | ||
01-31-2025 08:59 PM | ||
01-21-2025 05:40 PM | ||
01-21-2025 01:39 PM |
User | Count |
---|---|
17 | |
10 | |
7 | |
4 | |
4 |