How do you stop broadcast traffic on this switch? 1548M
How do you stop broadcast traffic on this switch? 1548M
We have a couple of Cat-6506's with MSFC's etherchannelled together on which we need to create loopback interfaces. Do these interfaces have to be on a separate subnets?Thanks.
At Present I am using No-name VOIP Routers and they are working fine. Now I want to replace them with Cisco Routers to get better results. I tried to configure them with Cisco "ConfigMaker" but I am facing lots of problem. I need help. I need a basi...
I'm not sure this is a question for this forum,but i will ask anyway.I have 2 2501's,1 2502, and a 1912 switch.My problem is as follows,with my laptop setup running win2000pro,i can run hyperterminal and it comes up fine without internet connection.M...
We have a couple of Layer 3 switches (Cat-6506) that are etherchannelled together. There are 8 Vlans defined on the switches and we need to configure HSRP on the vlan interfaces. When the HSRP is configured on a vlan int, what would be the default ga...
We were having problems with our 827H router, so I decided to reset it to the factory defaults and re-run the quick setup. I've done that before with no problems. This time, after it loads the configuration in the web setup, it keeps checking the mod...
Can someone please point me out to the doc dor configuring dlsw peers. Also, do I need to create a loopback interface in the MSFC (Cat-6506) if it's one of the peers?Thanks.
Anyone know how I can get IOS to stop prompting me to confirm filename when I save the startup-config and just go ahead and save it?R1#copy running-config startup-configDestination filename [startup-config]?I'm trying to script regular config saves, ...
Hi,I have a 192.168.0.0/24 network and a 192.168.1.0/24 network connected by a Cisco 1711.Even though the two networks are directly connected to each other, there is no routing done.From a host in 192.168.0.0/24, I can't ping any hosts in the 192.168...
I have not found the WIC-1ENET in ConfigMaker while configuring my Cisco 1751 Router. Need help.
Hi ALlI have two cisco routers connected over E1 via two serial interface on each other , I wants to limit B.W on the serial interface .Thanks in advance
I have a 1711-k9 router I am going to use for VPN. I have configured Fastethernet0 (the WAN port) with no problem. Its just standard ethernet.My problem is, that the LAN side is going through this WIC-4ESW switch.I am sure it is a wonderful tool. But...
I need to upgrade some 3550 switches to 12.1(20)EA1 Is the process of upgrading the IOS the same as say with the 4507's? Never upgraded the 3550's before. Thanks.
Ok...I said yes to erase the flash when I was moving a file into the router. Now, how do I get a bootable image back into flash? I am connected through telnet and am at a rommon prompt. Thanks - Wayne "eraserhead"
Hi all,Could anyone give me a suggestion to solve this problem ? I have searched from CCO but no relative question was found. Thanks !
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-13-2024 06:43 AM | ||
08-06-2024 12:40 PM | ||
08-05-2024 10:24 PM | ||
08-04-2024 01:12 PM | ||
08-01-2024 10:26 AM |
User | Count |
---|---|
7 | |
6 | |
5 | |
4 | |
3 |