Switching

I am a graduate student and work part-time for a financial services company. The company I work for is headquartered on the West Coast and will be opening an office on the East Coast by July 1.It is my responsibility to achieve a cost-efficient netwo...

Hello *I'm slightly confused about our new PIX 515. The device must response to three outside IP-Adresses (three different ipsec tunnels). But I can't get to create new interfaces on ethernet0. Either they are created with VLAN ID 1 or PDM complains...

I need to upgrade the code on my 6509's that are running in hybrid mode. I an having trouble specifying the code I need, Is there special code for msfc's or do they run any ios version out there. Is there any documents that explain how Cisco's relaes...

Hi all, I got questioned from my friend that his customer neet to connect new system (UNIX with TCP/IP) back to existing system running SNA. Are there any possible solution for such this conversion? is it able to be supported by Cisco gears?Thanks...

I wanted to ask if anybody could point me the right direction how to configure a 2811 router with two default gateways. I bought another port so I have two ethernets coming in and one going out to handle this.Thanks!

I have a 1760 Series Router with a Serial Interface that randomly goes up and down. According to our provider, they can find nothing wrong with the line. It is configured with a single Ethernet WIC (E0), and a single WAN Wic Card (S0). Configurati...

I'm trying to have users on an outside LAN (10.1.1.x) browse or use telnet services via PAT to an inside LAN (192.168.1.x). So a user browsing 'http://10.1.1.5:50000' would reach the web server on port 80 at 192.168.1.50.Here's the current rules. I'v...

We're NATing the destination addresses, using the ip NAT outside source static command and sending the NATed packets to a specific address through the defaut route (192.168.3.2). Does anybody happen to know if we can use the native address of the def...

Hi,Though its a very silly and basic question.....But i don't know it.How can i connect the fibre cable on the pc?????????Do we have some ethernet cards available for the same??????????????//Looking for response on ASAP.Thanks

HiI have a question in which i hope somebody can helpI have 2 router if I configure 10.1.1.1 255.0.0.0 on e0 for router1 and 10.1.1.2 255.0.0.0 on e0 for router2. After doing the above , I can ping both routers BUTi decide to change router1 e0 to 10....

A Chairde, I am trying to ping from Blade 3 (FastEthernet) port to Blade 1 (Fibre) on a 7609.From Console, I can ping both , but When source is FE and destination is Fibre , I cannot. I need to run NMAP on a Fibre Interface to see ports ope...

Hi,Iam integrating firewalls into our network which has connectivity to other vendors using Border routers running BGP. The distribution of these learned routes into our network is by OSPF. We are running OSPF in all switches to learn the routes betw...

Hi there,I've just updated my 837 ADSL router to IOS 12.3(11)T3, which is supposed to enable a second Ethernet port (using the physical FastEthernet 4 port) for DMZ use.I've successfully flashed the device, and followed the instructions:>Router(confi...

In our LAN basing the cisco switch 2950-24T, ALL PC can work good, but the powermac can't, they can't see together or can see few but can't connection,whether need to open Appletalk Protocal in this switch? but i can't see any about this command when...

I have a 1720 router and a WIC-1ENET when i first installed the Card it worked fine but my software package didnt have inter-vlan communication so i have upgraded to several different Options (i picked out software that cisco said could work with my ...