Dears I need Bill Of Material (BOM) for Main Part Number = WS-C3850-24T-E. Thank you
Forum Posts
Resolved! Flapping VLAN in c 2960X switch
We receive such log in 2960 X switch. Find attach switch configuration and image version..Feb 8 15:35:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan5, changed state to down.Feb 8 15:35:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vla...
I'm trying to apply speed 100 to a port on a 93180 with a GLC-TE or SFP-GE-T and getting the error (Transceiver speed does not match the speed configured on the port) SoftwareBIOS: version 07.64NXOS: version 9.2(1) IVNSUTAFcen02# show interface eth1/...
I have a Catalyst 3560 layer 3 switch and setup a default gateway on the vlan, but how do i connect a host that is not on any vlan to a host on a vlan.
Resolved! Auto Export Switch Data to CSV File
I'm looking to export my 9300 Cat switch data such as, interface(bandwidth, status) , CPU, Memory, to a CSV so I can ultimately pull that data from PowerBi. I would like this to be automated everyday if possibleHas anyone done this. Is it possible?
Resolved! Voice Vlan not working
In a single subnet total 10 2960-x switch install when I put new 2960-s series switch then in s series switch and x series(switch provide uplink to s series) IP telephone not working(It’s show verify your network connection) but data vlan working fin...
Resolved! VTP Issue
I have a topology with a couple switches separated by a few routers, working within a practice lab in Web-UI of GNS3.On both switches, I configured the interfaces leading to the routers as trunk ports using dot1Q encapsulation. I also set both to the...
Could someone please help me spec a switch with the following features?- Protocols: TCP/IP, EtherNet/IP, DHCP, BOOTP , IGMP, SMTP, STP, RSTP,MSTP, PVST+, VTP, SNMP, NTP- 48 ports (2 multimode Gb fiber ports)- 36 devices need 10/100 speed (RJ45 connec...
Hello,I want to create CCNA home lab. For the first time I bought 1841 router:------------------------------------------------------------Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 15.1(3)T2, RE LEASE SOFTWARE (fc1)Technical S...
Resolved! mixed stp version
Hi,I will lunch a bunch of SG series switches to my fabric.These switches have rapid stp enabled by default.In the same fabric i have a couple of older catalysts which support only pvst and rapid pvst.sg350 has option for pvst and rapid pvst, but bac...
HiI have ESXi server has 4 NICs, I used 2NICs For ESXi management these NICs connected to two different cisco switches and there is an Trunk between the switches, could this make L2 loop between cisco switches and VMware virtual switches? the connec...
Resolved! L3 STIG requirement help
I posted a previous discussion in another community regarding a few requirements to make my Cisco C921-4P router/switch. Someone explained to me that some commands may not work with this platform. specifically the ones below. Disable Gratuitous ARPD...
Hi, Can I kindly ask your help with NAT PAT configuration done in Packet Tracer? Configured NAT PAT on R2, and as soon as it is configured, no ping goes between inside and outside network. All routers know routes to each other, and all ping commands ...
Resolved! ACL block TCP traffic one way.
Hi,Got servers in vlan 10 ip range 10.0.0.0 and servers in vlan 20 ip range 20.0.0.0 at the same layer 3 switch. (c6509 sup720)I would like to block TCP traffic initiated from Vlan 20 to Vlan 10.But the servers in Vlan 10 needs to be able to open an ...
Hi to everyone.I´m trying to configure port forwarding in a Cisco RV340 router but I need to enable that only for certain source IPs not for all the internet. In that router when you create a new port forwading, it automaticaly generate a new access ...
