Bundle-Ether in ASR 9K is down

[pardeep.sharma8681]

Hi,

I am working on asr9k at VIRL simulator. I have configured bundle-ether channel in asr9k routers. Both routers are connected each other. Both are OSPF neighbors and BGP neighbors. I have configured bundle ether channel between them but this budle-ether channel is not coming up.. I have troubleshooted it but no vail. If you have any idea about configuration of bundle-ether channel on IOS-XR, share with me.
configuration is below;


at R2;

R2(config)#interface bundle-ether 10
R2(config-if)#no sh
R2(config-if)#ipv4 address 12.0.0.2 255.255.255.0

R2(config)#interface gi0/0/0/0
R2(config-if)#bundle id 10 mode active
R2(config-if)#no shut

R2(config)#interface gi0/0/0/1
R2(config-if)#bundle id 10 mode active
R2(config-if)#no shut

at R1
R1(config)#interface bundle-ether 10
R1(config-if)#no sh
R1(config-if)#ipv4 address 12.0.0.1 255.255.255.0

R1(config)#interface gi0/0/0/0
R1(config-if)#bundle id 10 mode passive
R1(config-if)#no shut

R1(config)#interface gi0/0/0/1
R1(config-if)#bundle id 10 mode passive
R1(config-if)#no shut

But it is showing down by using "show ip int brief"

[azibnaseem]

Hi [@pardeep.sharma8681]  ,

Kindly post the configuration of show ether-channel summary command output.

Regards'

[pardeep.sharma8681]

Hi,

The command "sh ether-channel summary is feature of IOS-XE, so it will not work in XR. The output of "sh bundle" is below;

RP/0/0/CPU0:R2#sh bundle
Tue Feb 14 06:16:48.341 UTC
Bundle-Ether10
  Status:                                    Down
  Local links <active/standby/configured>:   0 / 0 / 2
  Local bandwidth <effective/available>:     0 (0) kbps
  MAC address (source):                      0241.837a.a403 (Chassis pool)
  Inter-chassis link:                        No
  Minimum active links / bandwidth:          1 / 1 kbps
  Maximum active links:                      64
  Wait while timer:                          2000 ms
  Load balancing:                            
    Link order signaling:                    Not configured
    Hash type:                               Default
    Locality threshold:                      None
  LACP:                                      Not operational
    Flap suppression timer:                  Off
    Cisco extensions:                        Disabled
    Non-revertive:                           Disabled
  mLACP:                                     Not configured
  IPv4 BFD:                                  Not configured

  Port                  Device           State        Port ID         B/W, kbps
  --------------------  ---------------  -----------  --------------  ----------
  Gi0/0/0/0             Local            Configured   0x0001, 0x0000     1000000
      Bundle is in the process of being replicated to this location
  Gi0/0/0/1             Local            Configured   0x0001, 0x0000     1000000
      Bundle is in the process of being replicated to this location
RP/0/0/CPU0:R2#

[azibnaseem]

Hi [@pardeep.sharma8681]  ,

Actually, I have created ether-channels on switched. I didn't have configured on XR yet. Let me make a lab & then I will let you know.

Regards'

[pardeep.sharma8681]

thanks for your efforts.

[azibnaseem]

Hi [@pardeep.sharma8681]  ,

I didn't have VIRL simulator. However i google it & found a documents related to IOS-XR bundling. Please read through if it is helpful for you otherwise let me know.

Regards' 

[sagar0602]

hey I know it is too late but do you remember how did you resolved the issue.

As i am having a similar in live network.

Thanks

sagar 

[sagar0602]

---

@pardeep.sharma8681 wrote:

Hi,

I am working on asr9k at VIRL simulator. I have configured bundle-ether channel in asr9k routers. Both routers are connected each other. Both are OSPF neighbors and BGP neighbors. I have configured bundle ether channel between them but this budle-ether channel is not coming up.. I have troubleshooted it but no vail. If you have any idea about configuration of bundle-ether channel on IOS-XR, share with me.
configuration is below;


at R2;

R2(config)#interface bundle-ether 10
R2(config-if)#no sh
R2(config-if)#ipv4 address 12.0.0.2 255.255.255.0

R2(config)#interface gi0/0/0/0
R2(config-if)#bundle id 10 mode active
R2(config-if)#no shut

R2(config)#interface gi0/0/0/1
R2(config-if)#bundle id 10 mode active
R2(config-if)#no shut

at R1
R1(config)#interface bundle-ether 10
R1(config-if)#no sh
R1(config-if)#ipv4 address 12.0.0.1 255.255.255.0

R1(config)#interface gi0/0/0/0
R1(config-if)#bundle id 10 mode passive
R1(config-if)#no shut

R1(config)#interface gi0/0/0/1
R1(config-if)#bundle id 10 mode passive
R1(config-if)#no shut

But it is showing down by using "show ip int brief"

---

hey I know it is too late but do you remember how did you resolved the issue.

As i am having a similar in live network.

Thanks

sagar