02-16-2020 03:41 AM
Hi
I have a C4507 on which I did a write erase followed by a redundancy reload shelf. I went about configuring however, I forgot to enter username and set logging local on console and had to do reset.
I pulled out the secondary and went about booting the switch from where in i have been in a continuous rommon mode. Once I issue boot bootflash: I would then be in the IOS. I have to do that on both the supervisor engines. Is there any way I can get this to function properly.
Directory of bootflash:/ 2 -rwx 18090440 Aug 20 2013 09:11:39 +00:00 cat4500-ipbasek9-mz.150-2.SG7.bin 59244544 bytes total (28751044 bytes free)
Chassis Type : WS-C4507R Power consumed by backplane : 40 Watts Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+------------------+----------- 1 2 Supervisor V 1000BaseX (GBIC) WS-X4516 2 2 Supervisor V 1000BaseX (GBIC) WS-X4516 3 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 4 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T 5 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T 6 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T 7 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T Mod Redundancy role Operating mode Redundancy status ----+-------------------+-------------------+---------------------------------- 1 Active Supervisor SSO Active 2 Standby Supervisor SSO Standby hot System Failures: ---------------- Power Supply: bad/off (see 'show power')
Redundant System Information : ------------------------------ Available system uptime = 6 minutes Switchovers system experienced = 0 Standby failures = 0 Last switchover reason = none Hardware Mode = Duplex Configured Redundancy Mode = Stateful Switchover Operating Redundancy Mode = Stateful Switchover Maintenance Mode = Disabled Communications = Up Current Processor Information : ------------------------------- Active Location = slot 1 Current Software state = ACTIVE Uptime in current state = 5 minutes Image Version = Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 15.0(2)SG7, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Wed 01-May-13 17:37 by prod_rel_team Configuration register = 0x2102 Peer Processor Information : ---------------------------- Standby Location = slot 2 Current Software state = STANDBY HOT Uptime in current state = 4 minutes Image Version = Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 15.0(2)SG7, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Wed 01-May-13 17:37 by prod_r BOOT = Configuration register = 0x2102
BOOT variable does not exist CONFIG_FILE variable does not exist BOOTLDR variable does not exist Configuration register is 0x2102 Standby BOOT variable = Standby CONFIG_FILE variable does not exist Standby BOOTLDR variable does not exist Standby Configuration register is 0x2102
Solved! Go to Solution.
02-16-2020 05:16 AM
BOOT variable does not exist CONFIG_FILE variable does not exist BOOTLDR variable does not exist
Follow the below steps after booting :
config t
Switch(config) boot system flash bootflash:cat4500-ipbasek9-mz.150-2.SG7.bin
end
write mem
check
#show bootvar
reload and let us know.
02-16-2020 03:45 AM
1) Could you check the conf-register value 2) Is there a valid boot image specified in the start-up config ?
M.
02-16-2020 05:16 AM
BOOT variable does not exist CONFIG_FILE variable does not exist BOOTLDR variable does not exist
Follow the below steps after booting :
config t
Switch(config) boot system flash bootflash:cat4500-ipbasek9-mz.150-2.SG7.bin
end
write mem
check
#show bootvar
reload and let us know.
02-16-2020 03:03 PM
02-17-2020 12:14 AM
Thank you all for the support.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: