01-17-2022 07:02 AM
Cisco IOS XE Software, Version 16.11.01
Switch#show interfaces twentyFiveGigE 1/0/29
TwentyFiveGigE1/0/29 is down, line protocol is down (notconnect)
Hardware is Twenty Five Gigabit Ethernet, address is cc7f.76a4.34bc (bia cc7f.76a4.34bc)
Description: TO_Xier-HJ-SW-F3-1_link
MTU 1500 bytes, BW 25000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, Auto-speed, link type is auto, media type is unknown
Fec is auto
Switch#show interfaces twentyFiveGigE 2/0/29 capabilities
TwentyFiveGigE2/0/29
Model: C9500-48Y4C
Type: unknown
Speed: 1000,10000,25000
Duplex: full
FEC: auto/off/cl74/cl108
Trunk encap. type: 802.1Q
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression: percentage(0-100)
Unicast suppression: percentage(0-100)
Multicast suppression: percentage(0-100)
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
Fast Start: yes
QoS scheduling: rx-(not configurable on per port basis),
tx-(2p6q3t)
CoS rewrite: yes
ToS rewrite: yes
UDLD: yes
Inline power: no
SPAN: source/destination
PortSecure: yes
Dot1x: yes
Diagnostic Monitoring: N/A
Breakout Support: not applicable
Using these SFP's on the C1000 is fine, but not when the C9500 and C1000 are interconnecting because the C9500 is not recognized. I can't confirm if it's my configuration or the device or module. Meanwhile, other interfaces on the C9500 have used the same module, but no problems.
Solved! Go to Solution.
01-17-2022 05:37 PM
The SFP type is compatible with the c9500 SFP- 10GBASE-SR
01-17-2022 08:36 AM
- What is the sfp-type used on the 9500 ? Check : https://tmgmatrix.cisco.com/?dr=81&npid=50 , also available in attachment.
M.
01-17-2022 05:37 PM
The SFP type is compatible with the c9500 SFP- 10GBASE-SR
01-17-2022 09:29 AM
Can you post both sides :
show interfaces twentyFiveGigE x/x/x trans
what SFP you using speed ? 10GB ? or 1GB or 25GB ?
01-17-2022 05:38 PM
show interfaces twentyFiveGigE 1/0/13 capabilities
TwentyFiveGigE1/0/13
Model: C9500-48Y4C
Type: unknown
Speed: 1000,10000,25000
Duplex: full
FEC: auto/off/cl74/cl108
Trunk encap. type: 802.1Q
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression: percentage(0-100)
Unicast suppression: percentage(0-100)
Multicast suppression: percentage(0-100)
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
Fast Start: yes
QoS scheduling: rx-(not configurable on per port basis),
tx-(2p6q3t)
CoS rewrite: yes
ToS rewrite: yes
UDLD: yes
Inline power: no
SPAN: source/destination
PortSecure: yes
Dot1x: yes
Diagnostic Monitoring: N/A
Breakout Support: not applicable
01-17-2022 02:00 PM
Reboot the 9500.
If the links go up it could, potentially, be CSCvs14641.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: