07-16-2019 09:39 AM
My device is not being recognized by #show power inline police. Here are some logging information that may be helpful. I would like to be able to control POE on this port.
With device plugged in...
#show power inline police gigabitEthernet 1/0/15
Interface Admin Oper Admin Oper Cutoff Oper
State State Police Police Power Power
--------- ------ ---------- ---------- ---------- ------ -----
Gi1/0/15 auto off none n/a n/a n/a
Without device plugged in...
#show power inline police gigabitEthernet 1/0/15
Interface Admin Oper Admin Oper Cutoff Oper
State State Police Police Power Power
--------- ------ ---------- ---------- ---------- ------ -----
Gi1/0/15 off off none n/a n/a n/a
#show controller power inline
Alchemy instance 0, address 0
Pending event flag : N N N N N N N N N N N N
Current State : 00 00 00 00 00 00
Current Event : 00 00 00 00 00 00
Timers : 00 00 00 00 00 00 00 00 00 00 00 00
Error State : 00 00 00 00 00 00
Error Code : 00 00 00 00 00 00 00 00 00 00 00 00
Power Status : N N N N N N N N N N N N
Auto Config : N N N N N N N N N N N N
Disconnect : N N N N N N N N N N N N
Detection Status : 44 44 44 44 44 44
Current Class : 00 00 00 00 00 00
Tweetie debug : 00 00 00 00
POE Commands pending at sub:
Command 0 on each port : 00 00 00 00 00 00
Command 1 on each port : 00 00 00 00 00 00
Command 2 on each port : 00 00 00 00 00 00
Command 3 on each port : 00 00 00 00 00 00
Alchemy instance 1, address E
Pending event flag : N N N N N N N N N N N N
Current State : 00 00 00 00 11 11
Current Event : 00 00 00 00 00 40
Timers : 00 00 00 00 00 00 00 00 07 07 0A 07
Error State : 00 00 00 00 00 10
Error Code : 00 00 00 00 00 00 00 00 00 00 00 00
Power Status : N N N N N N N N N N N N
Auto Config : N N N N N N N N Y Y Y Y
Disconnect : N N N N N N N N N N N N
Detection Status : 44 04 44 44 00 00
Current Class : 00 00 00 00 00 00
Tweetie debug : 00 00 00 00
POE Commands pending at sub:
Command 0 on each port : 00 00 00 00 00 00
Command 1 on each port : 00 00 00 00 00 00
Command 2 on each port : 00 00 00 00 00 00
Command 3 on each port : 00 00 00 00 00 00
(Watts) (Watts)
---------- --------------- --------------------
Gi1/0/15 30.0 18.0
Port 15 detection status is set to 0. How can this be changed to 4?
07-16-2019 11:39 AM
Hello Donald,
what device are you trying to connect to the port gi1/0/15 ?
You should verify to what POE standard the device declares to conform to.
Hope to help
Giuseppe
07-16-2019 02:08 PM
The device works fine in a different port. When I use the command "show power inline police", it shows the status when connected to another port.
Port 15 powers up the device but doesn't show the status. The port seems to be setup for POE always. You can't turn it off or disable it with CLI command like "power inline never"
Is there a problem with the port?
07-17-2019 07:03 AM
Here is what it looks like when the device is plugged into another port. I tried resetting the switch and configuring the switch again but that didn't work. Other logs indicate the port is active and communicating but the POE on Port 15 isn't controllable or detected. Is there a way to fix port 15?
Any help would be appreciated.. Thanks.
With device plugged in...
#show power inline police gigabitEthernet 1/0/14
Interface Admin Oper Admin Oper Cutoff Oper
State State Police Police Power Power
--------- ------ ---------- ---------- ---------- ------ -----
Gi1/0/14 auto on none n/a n/a 13.5
#show controller power inline
Alchemy instance 0, address 0
Pending event flag : N N N N N N N N N N N N
Current State : 00 00 00 00 00 00
Current Event : 00 00 00 00 00 00
Timers : 00 00 00 00 00 00 00 00 00 00 00 00
Error State : 00 00 00 00 00 00
Error Code : 00 00 00 00 00 00 00 00 00 00 00 00
Power Status : N N N N N N N N N N N N
Auto Config : N N N N N N N N N N N N
Disconnect : N N N N N N N N N N N N
Detection Status : 44 44 44 44 44 44
Current Class : 00 00 00 00 00 00
Tweetie debug : 00 00 00 00
POE Commands pending at sub:
Command 0 on each port : 00 00 00 00 00 00
Command 1 on each port : 00 00 00 00 00 00
Command 2 on each port : 00 00 00 00 00 00
Command 3 on each port : 00 00 00 00 00 00
Alchemy instance 1, address E
Pending event flag : N N N N N N N N N N N N
Current State : 01 00 00 00 11 11
Current Event : 00 00 00 00 00 40
Timers : 00 03 00 00 00 00 00 00 07 07 0A 07
Error State : 00 00 00 00 00 10
Error Code : 00 00 00 00 00 00 00 00 00 00 00 00
Power Status : N N N N N N N N N N N N
Auto Config : N Y N N N N N N Y Y Y Y
Disconnect : N N N N N N N N N N N N
Detection Status : 44 04 44 44 00 00
Current Class : 00 00 00 00 00 00
Tweetie debug : 00 00 00 00
POE Commands pending at sub:
Command 0 on each port : 00 00 00 00 00 00
Command 1 on each port : 00 00 00 00 00 00
Command 2 on each port : 00 00 00 00 00 00
Command 3 on each port : 00 00 00 00 00 00
(Watts) (Watts)
---------- --------------- --------------------
Gi1/0/14 30.0 18.0
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide