12-10-2013 12:08 AM - edited 03-07-2019 05:00 PM
I had to do a factory reset on a 881 router and no I can only access via direct console/serial connection. But I'm not sure what to do from here to get it to work.
Output from Hyperterminal:
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
C880 platform with 262144 Kbytes of main memory
Readonly ROMMON initialized
program load complete, entry point: 0x80020000, size: 0x1ee6708
Self decompressing the image : ##################
################################################################################1: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name
################################################################################reboot level = advsecurity and License = advsecurity
################################################################################C: Crypto engine: onboard 0 State changed
[OK]
Restricted Rights Legendtialized
Dec 10 08:36:
Use, duplication, or disclosure by the Government isState changed
subject to restrictions as set forth in subparagraphd
Dec 10 08:36:23.079: %LINK-3-UPDOWN: I
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph5-UPDOWN: Line protocol on
t4, c
cisco Systems, Inc.
Dec 10 08:36:25.
170 West Tasman DrivestEthernet4, changed state to d
San Jose, California 95134-1706
own
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, R
Dec 10 08:36:28.483
ELEASE SOFTWARE (fc1)em restarted --
Technical Support: http://www.cisco.com/techsupportisco IOS Software, C880 Software (C880DATA-UNIVERSA
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 21-Mar-12 00:27 by prod_rel_team
Technical Support: http://www.ci
This product contains cryptographic features and is subje
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you8:36:29.483: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEther
agree to comply with applicable laws and regulations. If you are unable
t1, changed state to down
Dec 10 08
to comply with U.S. and local laws, return this product immediately.ne
p
Dec 10 08:36:31.499: %LINEPROTO-5
export@cisco.com.ocol on Interface
Installed image archive
Cisco 881 (MPC8300) processor (revision 1.0) with 236544K/25600K bytes of memory
Dec 10 08:36:34.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface
.s
Processor board ID FGL164227LM
5 FastEthernet interfaces
t4, changed state to dow
1 Virtual Private Network (VPN) Module:35.079: %LINK-3-UPDOWN: Interface Fas
256K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/ termianl
Press RETURN to get started! ^
%
Jan 2 12:00:02.351: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module nameaging>config
Translating "config"...domain server (255.255.255.
= c880-data Next reboot level = advsecurity and License = advsecuritydress or host name
% Unknown command or c
Dec 10 09:05:07.151: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed
nwbstaging>terminal
% I
to: Initialized.
Dec 10 09:05:07.271: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed
% Invalid input detected at '^' marker.
to: Enabled>setup
Dec 10 09:05:26.071: %LINK-3-UPDOWN: Interface FastEthernet4, changed state to u
% Bad IP address or h
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
own
Dec 10 09:05:31.599: %SYS-5-CONFIG_I: Configured from memory by console://www.cisco.com/techsupport
Dec 10 09:05:34.419: %SYS-5-RESTART: System restarted --
C880 platform with 2
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, Rnly ROMMON initialized
ELEASE SOFTWAR
ELEASE SOFTWAR
t2, changed state to down
Dec 10 09:05:35.419: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne
t3, changed state to down
nwbstaging>cisco
Translating "cisco"...domain server (255.255.255.255)
% Bad IP address or host name
% Unknown command or computer name, or unable to find computer address
nwbstaging>conf
Translating "conf"...domain server (255.255.255.255)
% Bad IP address or host name
% Unknown command or computer name, or unable to find computer address
nwbstaging>config
Translating "config"...domain server (255.255.255.255)
% Bad IP address or host name
% Unknown command or computer name, or unable to find computer address
nwbstaging>setup
Translating "setup"...domain server (255.255.255.255)
% Bad IP address or host name
% Unknown command or computer name, or unable to find computer address
nwbstaging>
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide