Hello,
I am using the SM-ES2-24-P module in a 2951 router. This is a layer 2 device, similar in capability to a Catalyst 2960. I had previously gotten it working using some instructions from a previous discussion I found here on the forums. But now, it isn't doing what I need, and I can't get into a console session using service-module.
I think there is something I don't fully understand about how this is supposed to connect with the router and pass traffic. Can anyone help?
I can see it with CDP:
Device ID: Switch
Entry address(es):
IP address: 10.2.2.2
Platform: cisco SM-ES2-24-P, Capabilities: Switch IGMP
Interface: GigabitEthernet1/1, Port ID (outgoing port): GigabitEthernet0/25
Holdtime : 124 sec
Version :
Cisco IOS Software, C2960SM Software (C2960SM-LANBASEK9-M), Version 12.2(52)EX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 13-May-10 13:53 by prod_rel_team
advertisement version: 2
Protocol Hello: OUI=0x00000C, Protocol ID=0x0112; payload len=27, value=00000000FFFFFFFF010221FF000000000000544A000D2B80FF0000
VTP Management Domain: ''
Native VLAN: 101
Duplex: full
Management address(es):
IP address: 10.2.2.2
C2951-2#service-module embedded-Service-Engine 0/0 session
Trying 10.2.2.1, 2002 ...
% Connection refused by remote host
;
sh ip int br
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 10.2.2.1 YES unset administratively down down
GigabitEthernet0/0 XXX.XXX.XXX.XX YES NVRAM up up
GigabitEthernet0/1 10.0.0.230 YES NVRAM down down
GigabitEthernet0/2 10.0.6.1 YES NVRAM up up
GigabitEthernet1/0 unassigned YES NVRAM administratively down down
GigabitEthernet1/1 unassigned YES unset up up
Loopback0 192.168.61.1 YES NVRAM up up
Loopback1 192.168.62.1 YES NVRAM up up
NVI0 192.168.61.1 YES unset up up
Tunnel0 192.168.91.1 YES NVRAM up down
Tunnel1 192.168.6.2 YES NVRAM up up
Virtual-Access1 unassigned YES unset down down
Virtual-Template2 192.168.62.1 YES unset down down
Vlan1 unassigned YES unset up up
Vlan2 10.2.2.1 YES NVRAM up up
Vlan101 10.0.101.1 YES manual up up
______
config:
interface Embedded-Service-Engine0/0
ip unnumbered Vlan2
interface GigabitEthernet0/0
ip address XXX.XXX.XXX.XX 255.255.255.128
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly in
duplex auto
speed 100
no cdp enable
crypto map WIN_OUTSIDE_STRONG_MAP
interface GigabitEthernet0/2
ip address 10.0.6.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet1/0
no ip address
shutdown
interface GigabitEthernet0/1
ip address 10.0.0.230 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet1/1
switchport access vlan 2
switchport trunk native vlan 101
switchport mode trunk
no ip address
!
interface Virtual-Template2
ip unnumbered Loopback1
peer default ip address dhcp-pool dhcp-vlan99-pool
!
interface Vlan1
no ip address
!
interface Vlan2
ip address 10.2.2.1 255.255.255.0
!
interface Vlan101
ip address 10.0.101.1 255.255.255.0
line 2
access-class 20 in
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
access-class 20 in
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
flowcontrol software
line vty 0 4
access-class 20 in
exec-timeout 90 0
transport input ssh
line vty 5 15
access-class 20 in
transport input ssh
!
