05-06-2015 12:58 AM - edited 03-07-2019 11:53 PM
Hi team,
Can WS-4506E support WS-X45-SUP6L-E? Also it is unable to load any other IOS except cat4500e-lanbase-mz.122-53.SG10.bin, I am trying to load the enterprise pack but it is not successful, am I missing something?
Thank you very much.
NAME: "Switch System", DESCR: "Cisco Systems, Inc. WS-C4506-E 6 slot switch "
PID: WS-C4506-E , VID: V03 , SN:
NAME: "Linecard(slot 1)", DESCR: "Supervisor 6L-E 10GE (X2), 1000BaseX (SFP)with 2 10GE X2 ports"
PID: WS-X45-SUP6L-E , VID: V07 , SN:
BPTP2.CS2#sho mod
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 6 Sup 6L-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6L-E JAE180
2 0 Unsupported module WS-X4612-SFP-E JAE180
3 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE180
4 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE180
WSJJ-01#dir
Directory of bootflash:/
6 -rw- 22820120 Mar 11 2014 23:00:30 +08:00 cat4500e-lanbase-mz.122-53.SG10.bin
7 -rw- 24910224 May 6 2015 08:31:22 +08:00 cat4500e-entservices-mz.122-53.SG10.bin
128165888 bytes total (73015296 bytes free)
Checking the partition table and boot sector...
Checking FAT, Files and Directories...
Reclaiming unused space...
Updating FAT...
Rom Monitor Program Version 12.2(44r)SG10
CPU Rev: 3.1, Board Rev: 13, Board Type: 103, CPLD Nexu Rev: 14
Chassis: WS-C4506-E
Front Panel Phy is Bcm5482s
Got Mac Address: 00:21:1c:7d:ae:06
MAC Address : 00-21-1c-7d-ae-06
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
Peer supervisor not detected or is not running IOS
Supervisor uplinks and all linecards have been reset
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. . . . .
******** The system will autoboot now ********
config-register = 0x2101
Autobooting using the first file from bootflash.....
Rommon reg: 0x00004380
Reset2Reg: 0x00008EFF
#
Darkside controller 0x0B435623..0x0B4439D5 original size:0x00012092##
Fortooine controller 0x0B56E594..0x0B6AA224 original size:0x001A8529
#############
Rommon reg: 0x00004380
Reset2Reg: 0x00008EFF
#
Darkside controller 0x0B435623..0x0B4439D5 original size:0x00012092##
Fortooine controller 0x0B56E594..0x0B6AA224 original size:0x001A8529
#################
diagsk5 version 4.1.0
prod: WS-X45-SUP6L-E part: 73-14276-02 serial: JAE18020566
Power-on-self-test for Module 1: WS-X45-SUP6L-E
Test Status: (. = Pass, F = Fail, U = Untested)
CPU Subsystem Tests ...
seeprom: Pass
Traffic: L3 Looopback ...
Test Results: Pass
Traffic: L2 Loopback ...
Test Results: Pass
Switching Subsystem Memory ...
Packet Memory Test Results: Pass
Module 1 Passed
Rommon reg: 0x00000380
######################################################
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-LANBASE-M), Version 12.2(53)SG10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Fri 13-Dec-13 13:04 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x121BF974
cisco WS-C4506-E (MPC8548) processor (revision 13) with 524288K bytes of memory.
Processor board ID FXS1804Q66K4
MPC8548 CPU at 1GHz, Supervisor 6L-E
Last reset from Reload
1 Virtual Ethernet interface
100 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Solved! Go to Solution.
05-06-2015 07:50 AM
You need 12.2(54)SG or later.
See this link and go to your specific module -
Jon
05-06-2015 04:18 AM
Yes it can support it as your link shows.
What is the exact problem you are facing with the new IOS ie. do you still have the current image as well as the new one in flash ?
If so your configuration register is set to 0x2101 which tells the switch to boot the first image it finds in flash which will be the one you are currently using.
So you would need to tell the switch to use the new image.
If the above is correct can you post a "sh bootvar" from the switch.
Jon
05-06-2015 07:29 AM
Hi Jon,
Thanks a lot for your advice.
I was trying to upgrade the IOS to see if it can support the module, yes you are right, I change the config-register to 0x2102 and it boots the enterprise version.
However, the switch is still unable to support the WS-X4612-SFP-E module. I am using cat4500e-entservices-mz.122-53.SG10.bin.
BPTP2.CS2#sh mod
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 6 Sup 6L-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6L-E JAE18099HQQ
2 0 Unsupported module WS-X4612-SFP-E JAE180020DZ6
3 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE18030770
4 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE180888UY
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 b838.61fd.9400 to b838.61fd.9405 1.0 12.2(44r)SG1 12.2(53)SG10 Ok
2 3c08.f6d3.31c4 to 3c08.f6d3.31cf 2.0 Unsupport
3 3c08.f6bd.ea64 to 3c08.f6bd.ea93 3.1 Ok
4 b838.6143.d1c0 to b838.6143.d1ef 3.1 Ok
05-06-2015 07:50 AM
You need 12.2(54)SG or later.
See this link and go to your specific module -
Jon
05-06-2015 08:56 AM
Hi Jon,
Thanks a lot, I will try this out.
Thank you very much.
Paul
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide