I have a cisco 4948 switch that im attemting to boot to 0x2142 but when the switch boots it boots from 0x2141
not sure why this is happening, my output form my switch is
**********************************************************
* *
* Welcome to Rom Monitor for WS-C4948 System. *
* Copyright (c) 2003-2007 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.2(31r)SGA2
Supervisor: WS-C4948 Chassis: WS-C4948
Hardware Revisions - Board: 6.0 CPLD: 5 Dagobah: 226
MAC Address : ************************ (Removed for Security)
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
Main Memory : 256 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. .
Autoboot cancelled......... please wait!!!
rommon 1 > [interrupt]
rommon 1 >set
PS1=rommon ! >
Fa1Enable=1
CV=tftp://10.1.1.1/cat4000-i9s-mz.122-25.EWA7.bin
RommonVer=12.2(31r)SGA2
DiagMonitorAction=Normal
BOOT=bootflash:cat4500-entservices-mz.122-53.SG5.bin,1;
RET_2_RTS=07:36:10 UTC Tue May 8 2012
RET_2_RCALTS=
DebugCallHome=00000
ConfigReg=0x2101
BootedFileName=bootflash:cat4500-entservicesk9-mz.150-2.SG4.bin
ConsecPostPassedCnt=31
rommon 2 >confreg
Configuration Summary :
=> load rom after netboot fails
=> console baud: 9600
=> autoboot from: the first file from internal flash device
do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]: n
enable "use net in IP bcast address"? y/n [n]: n
disable "load rom after netboot fails"? y/n [n]: n
enable "use all zero broadcast"? y/n [n]: n
enable "break/abort has effect"? y/n [n]: n
enable "ignore system config info"? y/n [n]: y
change console baud rate? y/n [n]: n
change the boot characteristics? y/n [n]: n
Configuration Summary :
=> load rom after netboot fails
=> ignore system config info
=> console baud: 9600
=> autoboot from: the first file from internal flash device
do you wish to save this configuration? y/n [n]: y
You must reset or power cycle for new configuration to take effect
rommon 3 >confreg 0x2142
usage: confreg
rommon 4 >reset
Resetting .......
rommon 5 >
**********************************************************
* *
* Welcome to Rom Monitor for WS-C4948 System. *
* Copyright (c) 2003-2007 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.2(31r)SGA2
Supervisor: WS-C4948 Chassis: WS-C4948
Hardware Revisions - Board: 6.0 CPLD: 5 Dagobah: 226
MAC Address : ************************ (Removed for Security)
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
Main Memory : 256 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. . . . .
******** The system will autoboot now ********
config-register = 0x2141
Autobooting using the first file from bootflash.....
Rommon reg: 0xE2004180
###########
k2diags version 5.7
prod: WS-C4948 part: 73-9130-13 serial: FOX1543G809
Power-on-self-test for Module 1: WS-C4948
Port/Test Status: (. = Pass, F = Fail, U = Untested)
Cpu Subsystem Tests ...
seeprom: . temperature_sensor: .
Port Traffic: L2 Asic Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: .
36: . 37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: .
Port Traffic: L3 Asic Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: .
36: . 37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: .
Switch Subsystem Memory ...
1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: . 12: .
13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .
25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: .
37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .
49: . 50: . 51: . 52: . 53: . 54: . 55: .
Module 1 Passed
Exiting to ios...
Rommon reg: 0xE2000180
#######################################################
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 15.0(2)SG4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Mon 19-Mar-12 15:45 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x123A4A88
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C4948 (MPC8245) processor (revision 0) with 262144K bytes of memory.
Processor board ID FOX1543G809
MPC8245 CPU at 266Mhz, Fixed Module
Last reset from PowerUp
1 Virtual Ethernet interface
48 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Press RETURN to get started!
*Jan 26 23:22:29.559: %C4K_IOSMODPORTMAN-4-POWERSUPPLYBAD: Power supply 2 has failed or been turned off
*Jan 26 23:22:38.831: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Jan 26 23:22:41.691: %SYS-6-STARTUP_CONFIG_IGNORED: System startup configuration is ignored based on the configuration register setting.
*Jan 26 23:22:41.915: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 1 (WS-C4948 S/N: FOX1543G809 Hw: 1.9) is online
*Jan 26 23:22:42.195: %SYS-5-RESTART: System restarted --
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 15.0(2)SG4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Mon 19-Mar-12 15:45 by prod_rel_team
*Jan 26 23:22:44.663: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=48: Transceiver has been inserted
Switch>
