cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
600
Views
0
Helpful
6
Replies
Highlighted

Catalyst 2960

I have Catalyst 2960 and trying to access the web console. Below is what the page shows. If I click on the web console I am getting an error saying http 404 not found. Any ideals what to try to get this to work?

Cisco Systems

Accessing Cisco WS-C2960-48TT-L "Switch"

Telnet - to the router.

Show interfaces - display the status of the interfaces.
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15

Show tech-support - display information commonly needed by tech support.
Extended Ping - Send extended ping commands.

Web Console - Manage the Switch through the web interface.

Help resources

  1. CCO at www.cisco.com - Cisco Connection Online, including the Technical Assistance Center (TAC).
  2. tac@cisco.com - e-mail the TAC.
  3. 1-800-553-2447 or +1-408-526-7209 - phone the TAC.
  4. cs-html@cisco.com - e-mail the HTML interface development group.
6 REPLIES 6
Highlighted
Hall of Fame Community Legend

Post the complete output to

Post the complete output to the CLI command of "dir". 

Hopefully this is what you

Hopefully this is what you was asking. I not good with Cisco switches or any thing so if this is not what you wanted let me know please. Thanks.

------------------ show flash: ------------------



Directory of flash:/

    2  -rwx        1048   Mar 1 1993 00:01:00 +00:00  multiple-fs
    3  -rwx     8471143  Feb 27 2013 00:42:17 +00:00  c2960-lanbasek9-mz.122-52.SE.bin
    5  -rwx     5709294  Oct 19 2007 03:51:55 +00:00  c2960-lanbasek9-mz.122-35.SE1.bin

32514048 bytes total (18330624 bytes free)
Highlighted
Hall of Fame Community Legend

3 -rwx 8471143 Feb 27

    3  -rwx     8471143  Feb 27 2013 00:42:17 +00:00  c2960-lanbasek9-mz.122-52.SE.bin
    5  -rwx     5709294  Oct 19 2007 03:51:55 +00:00  c2960-lanbasek9-mz.122-35.SE1.bin

Ok, the error message makes sense because there is no HTML pages in the flash directory. 

If GUI is required then the complete TAR file will need to be unpacked into the switch.  The TAR file has the complete set of HTML files needed for GUI.

Highlighted

So what file do I need to

So what file do I need to download? And is this very hard to upload it to the switch? Reason I am trying to use the web version is because I don't know the commands and all that to do this using telnet or other utilities. Would this be the file LAN BASE WITH WEB BASED DEV MGR 
c2960-lanbasek9-tar.122-52.SE.tar ?

Highlighted
Hall of Fame Community Legend

So what file do I need to

So what file do I need to download?

Download the file "c2960-lanbasek9-tar.122-55.SE10.tar".  Use this version as it is very stable.  

And is this very hard to upload it to the switch?

The CLI command is:  archive download-sw tftp://<TFTP IP address>/c2960-lanbasek9-tar.122-55.SE10.tar

Highlighted

Re: So what file do I need to

Where I can get the c2960-lanbasek9-tar.122-52.SE.tar file?

CreatePlease to create content
Content for Community-Ad