11-10-2014 11:22 AM - edited 03-07-2019 09:27 PM
I've got DHCP turned on using a 4506e (version 15) for my APs. When doing a show ip dhcp bind, the mac addresses for the APs show a lease, but does not show the address in CDP neighbor, making them unreachable. Can someone provide answers?
Bind
10.78.243.2 01e0.5fb9.43bb.b3 Nov 10 2014 01:25 PM Automatic
10.78.243.3 0150.3de5.8637.51 Nov 10 2014 01:25 PM Automatic
10.78.243.4 01c8.9c1d.f459.15 Nov 10 2014 01:25 PM Automatic
10.78.243.5 0150.3de5.8638.d1 Nov 10 2014 01:25 PM Automatic
10.78.243.6 01e0.5fb9.43bb.0c Nov 10 2014 01:25 PM Automatic
10.78.243.7 01e0.5fb9.43a2.10 Nov 10 2014 01:25 PM Automatic
10.78.243.8 0150.3de5.9326.7c Nov 10 2014 01:25 PM Automatic
10.78.243.9 01e0.5fb9.43bb.67 Nov 10 2014 01:25 PM Automatic
10.78.243.10 0150.3de5.8638.cf Nov 10 2014 01:25 PM Automatic
10.78.243.11 01e0.5fb9.43a7.ea Nov 10 2014 01:25 PM Automatic
10.78.243.12 01e0.5fb9.43a7.f9 Nov 10 2014 01:25 PM Automatic
10.78.243.13 0150.3de5.2f82.d2 Nov 10 2014 01:25 PM Automatic
10.78.243.14 0140.5539.ca94.d5 Nov 10 2014 01:25 PM Automatic
10.78.243.15 0150.3de5.8637.15 Nov 10 2014 01:25 PM Automatic
10.78.243.16 0130.e4db.8272.5c Nov 10 2014 01:25 PM Automatic
10.78.243.17 0140.5539.ca37.05 Nov 10 2014 01:25 PM Automatic
10.78.243.18 01e0.5fb9.43bb.7b Nov 10 2014 01:25 PM Automatic
CDP Neighbor
Device ID: name-ap18
Entry address(es):
Platform: cisco AIR-CAP3502I-A-K9, Capabilities: Router Trans-Bridge
Interface: GigabitEthernet4/1, Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 164 sec
Version :
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.2(4)JB3, RELEASE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 18-Dec-13 21:36 by prod_rel_team
advertisement version: 2
Duplex: full
Power drawn: 15.400 Watts
Power request id: 28353, Power management id: 2
Power request levels are:15400 14500 0 0 0
Management address(es):
11-10-2014 12:52 PM
Hello
cluster enable STAN
sh cluster candidates
|---Upstream---|
MAC Address Name Device Type PortIf FEC Hops SN PortIf FEC
xxxx.xxxxx.xxx ??????? Fax/x 1 1 Fax/x
SW#(config) cluster member 10 mac-address xxxx.xxxx.xxxx password stan ( enable password of remote switch)
sh cluster members
SN MAC Address Name PortIf FEC Hops SN PortIf FEC State
10 xxxx.xxxx.xxxx Fax/x 1 1 Fax/x Up
SW# rcommand 10
Then check the config of the aps
res
Paul
11-10-2014 01:27 PM
Paul, this did not work for us.
11-10-2014 01:56 PM
When doing a show ip dhcp bind, the mac addresses for the APs show a lease, but does not show the address in CDP neighbor,
Maybe CDP is disabled on the interface/globally?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide